
The AirTAC SE63 Standard Cylinder SE63X440S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø63mm bore and 440mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE63X440S is a double-acting, single-rod ISO 15552 profile cylinder engineered for mid-to-high force tasks, delivering a 1559 N push at 0.5 MPa. Its square extruded aluminum barrel omits external tie rods, yielding a flush, corrosion-resistant body that simplifies mounting and reduces machine footprint.
Equipped with a built-in position magnet (-S), this unit directly supports AirTAC CMSE reed and DMSE electronic sensors for precise end-of-stroke detection. Field-adjustable air cushioning at both ends allows technicians to tune deceleration on the fly, softening hard impacts during high-speed 440 mm traverses.
| Model | Airtac SE63 Standard Cylinder SE63X440S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø63 mm |
| Stroke | 440 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 1559 N | 1402 N |
| 0.7 MPa | 2182 N | — |
| Max (@1.0 MPa) | 318 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 63 | Bore size in mm. |
| ×440 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Actuates a routing gate on a 1.5 m roller conveyor, using the 440 mm stroke to shift pallets cleanly between packaging lanes.
Deploys a 440 mm sweep arm to fold major corrugated box flaps prior to hot-melt sealing, capitalizing on 1559 N of push force.
Positions a hardened steel backgauge finger on a press brake, using the -S magnet and DMSE sensors to confirm gauge depth.
Selecting the SE63X440S places you in a robust force band, delivering 1559 N of push force at 0.5 MPa. If your payload is lighter, stepping down to the 50 mm bore yields 982 N of push, while upgrading to the 80 mm bore provides 2513 N for heavier loads. Because this 440 mm stroke creates a long unsupported piston rod, integrating an external guide rail is critical to prevent rod-bearing bending and premature seal wear.
As a dimensionally interchangeable ISO 15552 cylinder, it serves as a direct replacement for other standard profile cylinders, matching the 63 mm bore, 440 mm stroke, PT3/8 port, and standard mounting accessories. Note that while its adjustable cushions decelerate the piston near stroke end, a plain SE cylinder cannot hold a load if air pressure is lost; for dead-end holding, consider the BSE rod lock variant.
AirtacDistr lists every SE63 order code with its price on one page at https://airtacdistr.com/products/airtac-se63-iso-air-cylinder
Quick checklist
At 0.5 MPa, the 63 mm bore provides 1559 N of push and 1402 N of pull force. At 0.7 MPa, push increases to 2182 N, with a maximum push capacity of 318 kgf at 1.0 MPa. The operational speed range is 30-800 mm/s.
Yes, the SE63X440S is dimensionally interchangeable per ISO 15552 standards. It shares the same mounting interface, PT3/8 port size, and 440 mm stroke as other standard profile cylinders, allowing for a direct retrofit without modifying the machine frame.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.