
The AirTAC SE63 Standard Cylinder SE63X50SH is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø63mm bore and 50mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE63X50SH is a double-acting single-rod profile cylinder built to the ISO 15552 standard, delivering a robust 1559 N push at 0.5 MPa. Its square extruded aluminum barrel omits external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machine frames. The integrated -S magnet enables precise end-position detection with CMSE reed or DMSE electronic sensors.
Equipped with a high-temperature FKM (Viton) seal, this unit operates reliably from -20 to 150 C in aggressive thermal environments. Field-adjustable air cushioning at both ends allows technicians to tune end-of-stroke deceleration, protecting tooling during rapid 50 mm strokes.
| Model | Airtac SE63 Standard Cylinder SE63X50SH |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø63 mm |
| Stroke | 50 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 1559 N | 1402 N |
| 0.7 MPa | 2182 N | — |
| Max (@1.0 MPa) | 318 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 63 | Bore size in mm. |
| ×50 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Uses the 1559 N extend force and 50 mm stroke to positively eject hot plastic parts, leveraging the FKM seal to withstand ambient radiant heat up to 150 C.
Applies steady clamping pressure on packaging film lines, where the adjustable cushion softens the hard mechanical stop during high-speed 50 mm cycles.
Shifts small metal stampings between press stations, relying on the -S magnet and DMSE sensors to confirm part movement in automated cells.
This 63 mm bore provides 1559 N push at 0.5 MPa, sitting perfectly between the 50 mm bore (982 N push) and the 80 mm bore (2513 N push) for mid-weight actuation. If your application demands position holding upon air loss, note that a standard SE cylinder will drift; you should step up to the BSE rod-lock variant or utilize an external pilot-operated check valve. As a true ISO 15552 profile cylinder, it offers a direct dimensional replacement for any equivalent 63 mm bore, 50 mm stroke cylinder with a PT3/8 port and standard mounting accessories.
AirtacDistr lists every SE63 order code with its price on one page at https://airtacdistr.com/products/airtac-se63-iso-air-cylinder
Quick checklist
At 0.5 MPa, this 63 mm bore cylinder provides 1559 N of push force and 1402 N of pull force. At 0.7 MPa, the push force increases to 2182 N, with a maximum push capacity of 318 kgf at 1.0 MPa. It operates at speeds ranging from 30-800 mm/s.
Yes, the SE63X50SH is dimensionally interchangeable with any standard ISO 15552 profile cylinder of the same bore and stroke. Additionally, its FKM (Viton) seal expands the operating temperature range up to 150 C, making it suitable for high-thermal environments where standard TPU seals would fail.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.