
The AirTAC SE63 Standard Cylinder SE63X560S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø63mm bore and 560mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE63X560S is a double-acting, single-rod ISO 15552 profile cylinder engineered for robust linear motion. It features a 63 mm bore and a 560 mm stroke, generating 1559 N of push force at 0.5 MPa and up to 2182 N at 0.7 MPa. The extruded aluminum barrel design omits external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machine frames.
Equipped with a built-in magnet (S option), this unit directly supports AirTAC CMSE reed and DMSE electronic position sensors without requiring external machining. Field-adjustable pneumatic cushioning at both ends allows technicians to tune end-of-stroke deceleration via a set screw, effectively softening hard impacts when cycling heavy loads at high speeds.
| Model | Airtac SE63 Standard Cylinder SE63X560S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø63 mm |
| Stroke | 560 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 1559 N | 1402 N |
| 0.7 MPa | 2182 N | — |
| Max (@1.0 MPa) | 318 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 63 | Bore size in mm. |
| ×560 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Executes 560 mm strokes to push heavy pallets onto secondary packaging lines, utilizing the 1559 N push force to overcome friction without bounce.
Drives the main folding arm in automated carton erectors, where the adjustable end cushions absorb kinetic energy to prevent tearing heavy cardboard.
Squares heavy-gauge steel sheets on press feed conveyors prior to stamping, relying on the 20 mm hard-chrome rod to resist deflection during edge contact.
Selecting the SE63X560S bridges the gap between mid-size and large-bore actuators. If 1559 N of push at 0.5 MPa is excessive for your payload, stepping down to the 50 mm bore yields 982 N. Conversely, if you need greater thrust, the 80 mm bore provides 2513 N. Because this model features a 560 mm stroke, the unsupported piston rod length increases bending moments under side loading; for heavy off-center loads, integrate an external guide rail to prevent premature rod-bearing wear.
This cylinder is dimensionally interchangeable per ISO 15552, serving as a direct replacement for other ISO 15552 cylinders and shared mounting hardware. It uses a PT3/8 port and a 20 mm rod with an M16x1.5 thread. Note that a plain SE cylinder relies on continuous air pressure to maintain position; if air is lost or the valve is centered, the piston will drift and cannot hold a load. For absolute position holding, consider the BSE rod lock variant.
AirtacDistr lists every SE63 order code with its price on one page at https://airtacdistr.com/products/airtac-se63-iso-air-cylinder
Quick checklist
At 0.5 MPa, this 63 mm bore cylinder provides 1559 N of push force and 1402 N of pull force. At 0.7 MPa, the push force increases to 2182 N, with a maximum push capacity of 318 kgf at 1.0 MPa. It operates at speeds between 30 and 800 mm/s.
Yes, the SE63X560S is dimensionally interchangeable per ISO 15552, meaning it shares standard mounting footprint and rod thread dimensions (M16x1.5) with other ISO 15552 profile cylinders. The built-in magnet also allows seamless integration with AirTAC CMSE or DMSE sensors.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.