verified AirTAC China Authorized Export Seller shield 100% Genuine AirTAC Parts workspace_premium 1-Year Warranty
appsShop by Modelexpand_more
person shopping_cart Request a QuoteQuote
AirTAC SE Series · ISO 15552 Cylinder

Airtac SE63 Standard Cylinder SE63X700SH

The AirTAC SE63 Standard Cylinder SE63X700SH is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø63mm bore and 700mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.

  • BoreØ63 mm
  • Stroke700 mm
  • Port sizePT3/8
  • Acting typeDouble acting
  • Rod threadM16×1.5
  • CushionAdjustable, 36 mm
$190.26 $197.76Save 3% Standard model — usually dispatched in 3-5 days
Request a Quote
  • No minimum order. A single piece can be ordered.
  • Shipped from our own warehouse: most standard models dispatch in 3–5 days; custom and non-standard models take 8–10 business days. Transit time after that depends on the destination.
Compare every SE63 stroke, mounting and version on one page All SE63 codes →
verified Genuine AirTAC workspace_premium 1-year warranty bolt Reply in 7 h

About the Airtac SE63 Standard Cylinder SE63X700SH

The AirTAC SE63X700SH is a double-acting single-rod ISO 15552 profile cylinder engineered for demanding thermal environments. It delivers a robust 1559 N push force at 0.5 MPa and features a 700 mm stroke. Because it carries the H seal code, this unit uses FKM (Viton) elastomers that expand the operating temperature range up to 150 C, making it highly reliable in hot processing zones.

The extruded aluminum barrel design omits external tie rods, yielding a compact, corrosion-resistant body that mounts flush in tight machinery spaces. Equipped with a built-in position magnet (S code), the cylinder interfaces directly with AirTAC CMSE reed and DMSE electronic sensors along the three integrated sensor grooves. Field-adjustable pneumatic cushioning at both ends allows technicians to fine-tune end-of-stroke deceleration for heavy 63 mm bore loads.

Airtac SE63 Standard Cylinder SE63X700SH Technical Specifications

ModelAirtac SE63 Standard Cylinder SE63X700SH
SeriesSE ISO 15552 profile cylinder
Bore sizeØ63 mm
Stroke700 mm
Acting typeDouble acting
Port sizePT3/8
Rod threadM16×1.5
FluidAir (filtered by 40µm element)
Operating pressure0.15 – 1.0 MPa
Proof pressure1.5 MPa
Temperature-20 to +70 °C (0–150 °C with FKM seals)
Speed range30 – 800 mm/s
CushionAdjustable, 36 mm
Max strokeUp to 1500 mm

Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).

Theoretical Output Force (Ø63mm)

PressurePush forcePull force
0.5 MPa1559 N1402 N
0.7 MPa2182 N—
Max (@1.0 MPa)318 kgf

Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.

Model Code: Airtac SE63 Standard Cylinder SE63X700SH

SEISO 15552 / VDMA 24562 profile-barrel double-acting cylinder.
63Bore size in mm.
×700Stroke length in mm.
-SOptional built-in magnet for CMSE / DMSE sensor sensing.

Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).

Where the Airtac SE63 Standard Cylinder SE63X700SH Is Used

sync_alt

Thermoforming Mold Handling

Uses the 1559 N extend force to shift heavy plastic sheet molds within high-heat zones, leveraging the FKM Viton seals to maintain integrity up to 150 C without degrading.

conveyor_belt

Hot End Glass Container Pusher

Actuates a 700 mm stroke to clear lehr conveyor lines of stalled glassware, relying on the adjustable end cushions to softly decelerate fast-moving payloads.

factory

Powder Coating Oven Door

Cycles large batch oven doors where ambient heat would destroy standard TPU seals, utilizing the no-tie-rod profile to minimize heat retention crevices.

Is the Airtac SE63 Standard Cylinder SE63X700SH the Right Cylinder?

When sizing this 63 mm bore actuator, evaluate your force requirements carefully. Stepping down to a 50 mm bore yields 982 N push at 0.5 MPa, while stepping up to an 80 mm bore provides 2513 N push at 0.5 MPa. If your machinery must hold a vertical load without live air pressure, note that a standard SE cylinder will drift when air is exhausted or a valve is centered; you should specify a BSE rod lock variant or an external pilot-operated check valve for fail-safe holding.

This SE63X700SH is dimensionally interchangeable per ISO 15552 standards, serving as a direct replacement for other ISO 15552 profile cylinders without altering mounting footprints. It uses a PT3/8 port and an M16x1.5 rod thread. Because the 700 mm stroke creates a long unsupported rod span, side loads can induce bending stresses on the rod bearing; always utilize an external guide mechanism to prevent premature wear.

AirtacDistr lists every SE63 order code with its price on one page at https://airtacdistr.com/products/airtac-se63-iso-air-cylinder

Quick checklist

  • ✓ Required force at your working pressure
  • ✓ Stroke and mounting space
  • ✓ Port/thread type (PT/G)
  • ✓ Magnet (-S) for CMSE/DMSE sensors?
  • ✓ Side load — consider a guided cylinder
Ask an Engineer

Installation & Maintenance Notes

  • check Use clean air filtered to 40µm or finer.
  • check Keep within 0.15 – 1.0 MPa operating pressure.
  • check Avoid side load on the piston rod.
  • check Adjust end cushion screws for smooth stops.
  • check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
  • check Installation by qualified personnel per AirTAC docs.

Airtac SE63 Standard Cylinder SE63X700SH FAQ

At 0.5 MPa, this 63 mm bore cylinder provides 1559 N of push force and 1402 N of pull force. At 0.7 MPa, the push force increases to 2182 N. The absolute maximum push capacity is 318 kgf when operated at the maximum rated pressure of 1.0 MPa.

Yes. The SE63X700SH is dimensionally interchangeable per ISO 15552 standards, meaning it shares the exact same mounting interface and body envelope as other ISO 15552 profile cylinders. You can swap it in as a direct retrofit without modifying your existing machine tooling or mounting plates.

verified

Authorized Export Seller

Genuine AirTAC parts produced by AirTAC factory.

workspace_premium

1-Year Warranty

Covers non-human-caused product damage.

local_shipping

Fast Dispatch

Most standard models are dispatched in 3-5 days.

bolt

Fast Reply

Most inquiries answered within 7 hours.

Related AirTAC SE Cylinders

Request a Quote for Airtac SE63 Standard Cylinder SE63X700SH

Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.

Thank you. We received your request for SE63X700SH and will confirm price, availability and lead time — usually within 7 hours.

For the fastest response, keep the complete model number above and include a clear photo of the product label. If photo upload is unavailable, email photos to [email protected] with your model number.