
The AirTAC SEJ Adjustable Cylinder SEJ50X100-10S is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 10mm window, so this Ø50mm unit covers an effective stroke of 90–100mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ50X100-10S is a double-acting, double-rod ISO 15552 profile cylinder with a 10mm adjustable stroke window. A rod exits both ends, yielding identical annulus areas for equal force in both directions. You get 825 N each way at 0.5 MPa, and the retract end dials in over an effective 90-100 mm range.
A stop screw on the back rod lets you mechanically fine-tune the end position on the machine without swapping hardware. The extruded aluminum barrel omits external tie rods, and the -S magnet integrates cleanly with CMSE reed or DMSE electronic sensors for position feedback.
| Model | Airtac SEJ Adjustable Cylinder SEJ50X100-10S |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø50 mm |
| Nominal stroke | 100 mm |
| Adjustment window | 10 mm (90–100 mm) |
| Configuration | Double rod, double acting |
| Port size | PT1/4 |
| Rod thread | M16×1.5 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 10mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 825 N |
| 0.7 MPa | 1155 N |
| Max (@1.0 MPa) | 168 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 50 | Bore size in mm. |
| ×100 | Nominal stroke length in mm. |
| -10 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Dial the 10mm stop screw to precisely set a 90-100mm stroke for stamping pins, using the 825N both-way force to press evenly.
Adjust the retract end on the fly when switching box sizes, relying on the double-rod's equal push and pull to move folders accurately.
Fine-tune the nozzle height during commissioning, locking the back-rod stop screw once the exact 90-100mm dispense position is set.
Verify the 10mm adjustment window covers your positioning tolerance. If you need less force, the 40mm bore provides 528 N both ways at 0.5 MPa; if your load demands more, step up to the 63mm bore for 1402 N both ways. For fixed-stroke tasks without end-position tuning, a standard SED cylinder is sufficient.
This cylinder does not hold position on air loss; the adjustable air cushion at both ends only decelerates the piston near stroke end. For fail-safe holding, specify an external rod lock. As a dimensionally interchangeable ISO 15552 unit, match the 50mm bore, 100mm stroke, PT1/4 port, and your preferred mounting (Basic, FA, LB, TC, FTC, TCM1, TCM2) for direct replacement.
AirtacDistr lists every SEJ50 order code with its price on one page at https://airtacdistr.com/products/airtac-sej50-adjustable-cylinder
Quick checklist
A stop screw on the rear rod lets you mechanically shorten the retract stroke by up to 10mm. The effective stroke range is 90-100mm, which you lock in place after setting the exact end position.
Because it is a double-rod cylinder, force is equal in both directions: 825 N at 0.5 MPa, 1154 N at 0.7 MPa, and a maximum of 168 kgf at 1.0 MPa.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.