
The AirTAC SEJ Adjustable Cylinder SEJ50X100-20S is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 20mm window, so this Ø50mm unit covers an effective stroke of 80–100mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ50X100-20S is a double-acting, double-rod ISO 15552 profile cylinder with a 20mm adjustable stroke window, letting you dial the retract end from 80mm to 100mm. A rod exits both ends, meaning the annulus area is identical in both directions. This delivers an equal output force of 825 N each way at 0.5 MPa, preventing speed asymmetries common to single-rod units.
The stroke is set via a stop screw on the rear rod; you lock it after finding the exact machine position. This 50mm bore runs on PT1/4 ports, carries a 20mm rod with an M16x1.5 thread, and includes a magnet for CMSE or DMSE sensors. Adjustable air cushions at both ends decelerate the load near stroke end.
| Model | Airtac SEJ Adjustable Cylinder SEJ50X100-20S |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø50 mm |
| Nominal stroke | 100 mm |
| Adjustment window | 20 mm (80–100 mm) |
| Configuration | Double rod, double acting |
| Port size | PT1/4 |
| Rod thread | M16×1.5 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 20mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 825 N |
| 0.7 MPa | 1155 N |
| Max (@1.0 MPa) | 168 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 50 | Bore size in mm. |
| ×100 | Nominal stroke length in mm. |
| -20 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Adjust the rear stop screw to accommodate different carton heights on a packaging line, shifting the stroke end by up to 20mm without swapping hardware.
Verify the 20mm adjustment window covers your positioning range. If 825 N at 0.5 MPa is excessive, step down to the 40mm bore (528 N both ways); if undersized, step up to the 63mm bore (1402 N both ways). If you never need to fine-tune the end position, a fixed-stroke SED saves length. For drop prevention, note this cylinder does not hold position on air loss—use an external rod lock.
This 100mm stroke is short enough that side-load stress is minimal, but always align external guides with the M16x1.5 rod thread. Dimensionally interchangeable per ISO 15552, it supports Basic, FA, LB, TC, FTC, TCM1, and TCM2 mounts (omitting FB/CA/CB/CR). The -S magnet enables precise electronic DMSE or reed CMSE end-of-stroke detection.
AirtacDistr lists every SEJ50 order code with its price on one page at https://airtacdistr.com/products/airtac-sej50-adjustable-cylinder
Quick checklist
A stop screw on the rear rod mechanically limits the retract travel. You can dial the retract end position within a 20mm window, giving an effective stroke range of 80mm to 100mm. Once set, you lock the screw in place.
Because it is a double-rod cylinder, force is equal in both directions: 825 N at 0.5 MPa, 1154 N at 0.7 MPa, and a maximum of 168 kgf at 1.0 MPa.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.