verified AirTAC China Authorized Export Seller shield 100% Genuine AirTAC Parts workspace_premium 1-Year Warranty
appsShop by Modelexpand_more
person shopping_cart Request a QuoteQuote
AirTAC SEJ Series · ISO 15552 Adjustable-Stroke Cylinder

Airtac SEJ Adjustable Cylinder SEJ50X100-30S

The AirTAC SEJ Adjustable Cylinder SEJ50X100-30S is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 30mm window, so this Ø50mm unit covers an effective stroke of 70–100mm without changing cylinders. Force is equal in both directions.

  • BoreØ50 mm
  • Nominal stroke100 mm
  • Adjust window30 mm
  • Effective stroke70–100 mm
  • Port sizePT1/4
  • CushionAdjustable, 30 mm
$97.21 $104.71Save 7% Standard model — usually dispatched in 3-5 days
Request a Quote
  • No minimum order. A single piece can be ordered.
  • Shipped from our own warehouse: most standard models dispatch in 3–5 days; custom and non-standard models take 8–10 business days. Transit time after that depends on the destination.
Compare every SEJ50 stroke, mounting and version on one page All SEJ50 codes →
verified Genuine AirTAC workspace_premium 1-year warranty bolt Reply in 7 h

About the Airtac SEJ Adjustable Cylinder SEJ50X100-30S

The AirTAC SEJ50X100-30S is a double-acting, double-rod ISO 15552 profile cylinder with an adjustable stroke. A rod exits both ends, yielding identical annulus areas so the drive force is equal in both directions at 825 N each way at 0.5 MPa. The retract stroke covers an active 30 mm window, letting you dial the effective travel down from 100 mm to 70 mm without changing hardware.

You set the exact end-position using a stop screw on the back rod, then lock it down for rigid commissioning. The extruded aluminum barrel carries no external tie rods, and the -S magnet integrates directly with CMSE reed or DMSE electronic sensors for position feedback. Adjustable air cushions at both ends decelerate the motion near stroke end.

Airtac SEJ Adjustable Cylinder SEJ50X100-30S Technical Specifications

ModelAirtac SEJ Adjustable Cylinder SEJ50X100-30S
SeriesSEJ ISO 15552 adjustable-stroke cylinder
Bore sizeØ50 mm
Nominal stroke100 mm
Adjustment window30 mm (70–100 mm)
ConfigurationDouble rod, double acting
Port sizePT1/4
Rod threadM16×1.5
Operating pressure0.15 – 1.0 MPa
Proof pressure1.5 MPa
Temperature-20 to +70 °C (0–150 °C with FKM seals)
Speed range30 – 800 mm/s
CushionAdjustable, 30 mm

Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 30mm window. Port options: PT (standard) / G (BSPP).

Theoretical Output Force (Ø50mm)

PressureForce (both directions)
0.5 MPa825 N
0.7 MPa1155 N
Max (@1.0 MPa)168 kgf

A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.

Model Code: Airtac SEJ Adjustable Cylinder SEJ50X100-30S

SEJISO 15552 double-rod double-acting cylinder with adjustable stroke.
50Bore size in mm.
×100Nominal stroke length in mm.
-30Adjustment stroke window in mm (options: 10/20/30/40/50/75/100).
-SOptional built-in magnet for CMSE / DMSE sensor sensing.

Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).

Where the Airtac SEJ Adjustable Cylinder SEJ50X100-30S Is Used

tune

Press Feed Stop Calibration

Dial the 70-100 mm retract window to hit a precise sheet metal stop, leveraging the equal 825 N both-way force to hold the guide steady during press feed changeovers.

swap_horiz

Variable Part Ejection

Adjust the back-rod stop screw on the fly to eject different height stamped parts from a conveyor without swapping out the entire cylinder assembly.

precision_manufacturing

Assembly Pick-and-Place

Fine-tune the lower end position for placing electronic components, using the DMSE electronic sensors to verify the exact adjusted stroke before locking the mechanism.

Is the Airtac SEJ Adjustable Cylinder SEJ50X100-30S the Right Cylinder?

Verify the 30 mm adjustment window covers your required end-position range; this 50 mm bore provides 825 N both ways at 0.5 MPa. If your load is lighter, the neighboring 40 mm bore yields 528 N, while heavier setups step up to the 63 mm bore for 1402 N. A fixed-stroke SED is sufficient if you need no on-machine fine-tuning. For fail-safe load holding on air loss, add an external rod lock or use a BSED, as the stop screw and cushions are not brakes. Match the PT1/4 port, M16x1.5 rod thread, and your mounting choice from Basic, FA, LB, TC, FTC, TCM1, or TCM2.

AirtacDistr lists every SEJ50 order code with its price on one page at https://airtacdistr.com/products/airtac-sej50-adjustable-cylinder

Quick checklist

  • ✓ Need on-machine stroke fine-tuning?
  • ✓ Adjustment window (30mm) covers your range
  • ✓ Equal force both directions OK
  • ✓ Port/thread type (PT/G)
  • ✓ Magnet (-S) for CMSE/DMSE sensors?
Ask an Engineer

Installation & Maintenance Notes

  • check Use clean air filtered to 40µm or finer.
  • check Keep within 0.15 – 1.0 MPa operating pressure.
  • check Set the stop screw within the 30mm window; lock it after adjusting.
  • check Adjust end cushion screws for smooth stops.
  • check Use correct mounting accessory (LB/FA/TC/FTC/TCM1/TCM2).
  • check Installation by qualified personnel per AirTAC docs.

Airtac SEJ Adjustable Cylinder SEJ50X100-30S FAQ

A stop screw on the rear rod mechanically shortens the retract stroke over a 30 mm window. You can dial the effective travel from 70 mm up to the nominal 100 mm, then lock the screw to hold that precise end-position.

Because it is a double-rod cylinder, the force is identical in both directions. It provides 825 N at 0.5 MPa, 1154 N at 0.7 MPa, and a maximum of 168 kgf at 1.0 MPa.

verified

Authorized Export Seller

Genuine AirTAC parts produced by AirTAC factory.

workspace_premium

1-Year Warranty

Covers non-human-caused product damage.

local_shipping

Fast Dispatch

Most standard models are dispatched in 3-5 days.

bolt

Fast Reply

Most inquiries answered within 7 hours.

Related AirTAC SEJ Cylinders

Request a Quote for Airtac SEJ Adjustable Cylinder SEJ50X100-30S

Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.

Thank you. We received your request for SEJ50X100-30S and will confirm price, availability and lead time — usually within 7 hours.

For the fastest response, keep the complete model number above and include a clear photo of the product label. If photo upload is unavailable, email photos to [email protected] with your model number.