
The AirTAC SEJ Adjustable Cylinder SEJ50X125-30 is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 30mm window, so this Ø50mm unit covers an effective stroke of 95–125mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ50X125-30 is a double-acting, double-rod ISO 15552 profile cylinder featuring a 30mm adjustable stroke window. A stop screw on the back rod lets you dial in the retract end position, yielding an effective stroke range of 95-125mm for precise machine commissioning.
This bore 50mm unit uses a PT1/4 port and an M16x1.5 rod thread. It features field-adjustable air cushions at both ends to manage deceleration near stroke limits. Note that this specific SKU lacks a magnet, so it will not work with CMSE or DMSE position sensors without modification.
| Model | Airtac SEJ Adjustable Cylinder SEJ50X125-30 |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø50 mm |
| Nominal stroke | 125 mm |
| Adjustment window | 30 mm (95–125 mm) |
| Configuration | Double rod, double acting |
| Port size | PT1/4 |
| Rod thread | M16×1.5 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 30mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 825 N |
| 0.7 MPa | 1155 N |
| Max (@1.0 MPa) | 168 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 50 | Bore size in mm. |
| ×125 | Nominal stroke length in mm. |
| -30 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Dial the 30mm retract window to perfectly align a 1154N clamping stop for varying sheet metal bend lengths.
Adjust the effective stroke from 95 to 125mm to accommodate different carton heights without swapping hardware.
Fine-tune the exact adhesive extrusion endpoint during machine commissioning using the back-rod stop screw.
Confirm this 30mm adjustment window covers your required end-position variance. If you need less force, stepping down to the bore 40mm SEJ yields 528N at 0.5 MPa both ways; if your load is heavier, the bore 63mm SEJ provides 1962N at 0.7 MPa. If your end position never changes, a fixed-stroke SED cylinder is sufficient. For ISO 15552 replacement matching, verify the 125mm stroke, PT1/4 port, and required mounting from the Basic, FA, LB, TC, FTC, TCM1, or TCM2 subset.
Remember that a plain SEJ does not hold position on air loss. The adjustable air cushion and mechanical stop screw only set the end position and decelerate the load; they are not a fail-safe lock. For secure holding, use an external rod lock. Since the 125mm stroke is under 300mm, side-load stress is minimal, but external guides are still recommended for heavy lateral loads.
AirtacDistr lists every SEJ50 order code with its price on one page at https://airtacdistr.com/products/airtac-sej50-adjustable-cylinder
Quick checklist
A stop screw on the rear rod mechanically shortens the retract stroke over a 30mm window. You can set the effective stroke anywhere from 95mm up to the full 125mm, then lock it in place.
Because the rod exits both ends, force is identical in both directions. It provides 825N at 0.5 MPa, 1154N at 0.7 MPa, and a maximum of 168 kgf at 1.0 MPa.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.