
The AirTAC SEJ Adjustable Cylinder SEJ50X200-30S is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 30mm window, so this Ø50mm unit covers an effective stroke of 170–200mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ50X200-30S is a double-acting, double-rod ISO 15552 profile cylinder with a 30 mm adjustable stroke window, letting you dial the retract end from 170 to 200 mm. A rod exits both ends, yielding identical annulus areas so the drive force is equal in both directions at 825 N (0.5 MPa).
Because the barrel is an extruded aluminum profile, it omits external tie rods for a clean exterior. The rear rod houses a mechanical stop screw to set the exact end position, which you lock after dialing in the machine. An -S magnet is built in for CMSE reed or DMSE electronic sensors.
| Model | Airtac SEJ Adjustable Cylinder SEJ50X200-30S |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø50 mm |
| Nominal stroke | 200 mm |
| Adjustment window | 30 mm (170–200 mm) |
| Configuration | Double rod, double acting |
| Port size | PT1/4 |
| Rod thread | M16×1.5 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 30mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 825 N |
| 0.7 MPa | 1155 N |
| Max (@1.0 MPa) | 168 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 50 | Bore size in mm. |
| ×200 | Nominal stroke length in mm. |
| -30 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Adjust the retract stop from 170 to 200 mm to accommodate different carton heights on a packaging line without swapping hardware.
Set exact probe touch points on a PCB test fixture; the double-rod design prevents rod binding while the DMSE sensor confirms position.
Verify the 30 mm adjustment window covers your positioning range. If you need less force, the 40 mm bore delivers 528 N both ways at 0.5 MPa; if you need more, step up to the 63 mm bore for 1402 N. If you never need to fine-tune the end position, a fixed-stroke SED saves complexity.
This SEJ50X200-30S uses PT1/4 ports and a Ø20 mm rod. Note that a plain cylinder does not hold position on air loss; the adjustable air cushion decelerates near stroke end but is not a brake. For fail-safe holding, use an external rod lock.
AirtacDistr lists every SEJ50 order code with its price on one page at https://airtacdistr.com/products/airtac-sej50-adjustable-cylinder
Quick checklist
A stop screw on the back rod lets you shorten the retract stroke by up to 30 mm. The effective stroke range is 170 to 200 mm. You dial in the exact end position during commissioning and lock it mechanically.
Because the rod exits both ends, the force is identical in both directions. It provides 825 N at 0.5 MPa, 1154 N at 0.7 MPa, and a maximum of 168 kgf at 1.0 MPa.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.