
The AirTAC SEJ Adjustable Cylinder SEJ50X30-20S is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 20mm window, so this Ø50mm unit covers an effective stroke of 10–30mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ50X30-20S is a double-acting, double-rod ISO 15552 profile cylinder. A rod exits both ends, yielding identical annulus areas so thrust matches on extend and retract. You get 825 N each way at 0.5 MPa. A stop screw on the back rod lets you dial the retract end over a 20 mm window, setting the effective stroke anywhere from 10 mm to 30 mm.
Because it carries the -S magnet, it integrates directly with CMSE reed and DMSE electronic sensors for end-of-travel signaling. The extruded aluminum barrel is dimensionally interchangeable per ISO 15552, and adjustable air cushions at both ends decelerate the load near stroke end. Remember the cushion only softens the stop; it is not a mechanical lock.
| Model | Airtac SEJ Adjustable Cylinder SEJ50X30-20S |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø50 mm |
| Nominal stroke | 30 mm |
| Adjustment window | 20 mm (10–30 mm) |
| Configuration | Double rod, double acting |
| Port size | PT1/4 |
| Rod thread | M16×1.5 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 20mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 825 N |
| 0.7 MPa | 1155 N |
| Max (@1.0 MPa) | 168 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 50 | Bore size in mm. |
| ×30 | Nominal stroke length in mm. |
| -20 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Dial the 10 to 30 mm stroke to perfectly time a 825 N crimping press during commissioning without swapping hardware.
Adjust the retract stop on the fly to accommodate different material heights on a packaging line, leveraging the equal both-way force.
Use the 20 mm window to trial different end positions for a testing fixture, locking the back-rod screw once the optimal travel is found.
Confirm the 20 mm adjustment window covers your required end-position range. If you need less force, the adjacent 40 mm bore provides 528 N both ways at 0.5 MPa; if you need more, the 63 mm bore provides 1402 N. If you do not need to fine-tune the stroke on the machine, a fixed-stroke SED cylinder is sufficient. For drop-out fail-safe holding, use a BSED or external rod lock, as this standard SEJ does not hold position on air loss. Match your replacement by bore, stroke, 20 mm window, PT1/4 port, and mounting choice from Basic, FA, LB, TC, FTC, TCM1, or TCM2.
AirtacDistr lists every SEJ50 order code with its price on one page at https://airtacdistr.com/products/airtac-sej50-adjustable-cylinder
Quick checklist
A stop screw on the rear rod mechanically shortens the retract stroke. For this model, you can dial the end position over a 20 mm window, giving an effective stroke range of 10 mm to 30 mm. You lock the screw after setting the desired position.
Because the rod exits both ends, force is identical in both directions. It generates 825 N at 0.5 MPa, 1154 N at 0.7 MPa, and a maximum of 168 kgf at 1.0 MPa.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.