Airtac TACE Guided Compact Cylinder TACE32X5S
The AirTAC Airtac TACE Guided Compact Cylinder TACE32X5S is a genuine double acting, non-rotating ISO 21287 compact air cylinder with a Ø32mm bore and 5mm stroke, 1/8" air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder. Twin guide rods keep the tooling from rotating.
- BoreØ32 mm
- Stroke5 mm
- Port size1/8"
- Acting typeDouble acting, non-rotating
- Rod threadM8×1.25
- CushionFixed TPU bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac TACE Guided Compact Cylinder TACE32X5S
Built as a double acting, non-rotating ISO 21287 compact cylinder, the TACE32X5S pairs a 32 mm bore with a very short 5 mm stroke in a hard-anodized aluminium body with an S45C hard-chrome plated 12 mm rod. Twin guide rods on a yoke stop the tooling rotating and carry side load, so a gripper or plate stays square without an external guide. At 0.5 MPa it pushes 402.1 N and pulls 345.6 N; at 0.7 MPa those figures rise to 563 N and 483.8 N. The short body saves about 50% of the mounting length of an ISO 15552 profile cylinder, which is exactly what tight jigs and guarded cells need.
Plan on roughly 241 N of usable push at 0.5 MPa (about 0.6 of the rated force), which corresponds to lifting about 41 kg vertically on paper, or around 20 kg with a 2:1 margin. Because this model carries the -S code, the magnet is fitted, so CMSE or DMSE reed and solid-state switches can be clamped into the body slots to report the 5 mm end positions. A fixed TPU bumper at each end absorbs end-of-stroke energy, the port is 1/8" PT, the rod end carries a female M8x1.25 thread, and speed runs 30-500 mm/s at 0.15-1.0 MPa (22-145 psi).
Airtac TACE Guided Compact Cylinder TACE32X5S Technical Specifications
| Model | Airtac TACE Guided Compact Cylinder TACE32X5S |
|---|---|
| Series | TACE compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø32 mm |
| Stroke | 5 mm |
| Acting type | Double acting, non-rotating |
| Port size | 1/8" |
| Rod thread | M8×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating; guide rods: stainless steel (Ø12-40) / S45C (larger). Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
Theoretical Output Force (Ø32mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 402 N | 346 N |
| 0.7 MPa | 563 N | 484 N |
| Max (@1.0 MPa) | 82 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin. Twin guide rods stop the tooling rotating.
Model Code: Airtac TACE Guided Compact Cylinder TACE32X5S
| TACE | ISO 21287 compact cylinder (non-rotating (twin-guide yoke)). |
|---|---|
| 32 | Bore size in mm. |
| ×5 | Stroke length in mm. |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Where the Airtac TACE Guided Compact Cylinder TACE32X5S Is Used
In-jig part presence check
A 5 mm probe stroke confirms a machined housing is fully seated in its CNC fixture before cutting starts; the fitted -S magnet drives a CMSE switch straight to the PLC.
Connector ejection from a nest
With 402.1 N push at 0.5 MPa, the cylinder kicks a finished automotive connector clear of its assembly nest in one short hit - the twin-guide yoke keeps the push face from twisting.
Indexing pin on a dial table
A 5 mm locking pin engages a rotary indexing plate on a bottling line; misalignment side load is taken by the guide rods, not the 12 mm piston rod.
Is the Airtac TACE Guided Compact Cylinder TACE32X5S the Right Cylinder?
For a 5 mm confirm-or-nudge move, the TACE25X5S gives 245.4 N push at 0.5 MPa if your load is lighter, while the TACE40X5S reaches 628.3 N when you want more reserve on the same short stroke. The piston drifts if air is lost - it is not a lock - so add a rod lock or pilot check valve wherever a load must stay held. FB flange, CA/CB clevis, CR and FTC mountings all suit this compact body, and the fitted -S magnet lets CMSE / DMSE switches flag both ends of the 5 mm travel.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Short stroke fits the compact body
- ✓ Port/thread type (PT / G)
- ✓ Add -S if you need the magnet for sensors
- ✓ Rod type (female / male B) & mount (FA/LB/CA)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Compact body: keep the stroke short and avoid side load on the rod.
- check Do not dismantle the threaded front/back covers.
- check Keep speed within the rated range; the TPU bumper absorbs stroke-end energy.
- check Installation by qualified personnel per AirTAC docs.
Airtac TACE Guided Compact Cylinder TACE32X5S FAQ
At 0.5 MPa it pushes 402.1 N and pulls 345.6 N; at 0.7 MPa push rises to 563 N with pull at 483.8 N. The theoretical maximum at 1.0 MPa is 82 kgf. Operating pressure is 0.15-1.0 MPa (22-145 psi), speed 30-500 mm/s, and the 32 mm bore takes a 1/8" PT port with a female M8x1.25 rod thread.
The ISO 21287 short body saves about 50% of the mounting length of an ISO 15552 profile cylinder, and a fixed TPU bumper at each end absorbs end-of-stroke energy. FB flange, CA/CB clevis, CR and FTC mountings all fit. Since this model carries the -S code, the magnet is fitted and CMSE / DMSE reed or solid-state switches can be clamped in the body slots; models ordered without -S have no magnet.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac TACE Guided Compact Cylinder TACE32X5S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.