Airtac TACE Guided Compact Cylinder TACE32X65S
The AirTAC Airtac TACE Guided Compact Cylinder TACE32X65S is a genuine double acting, non-rotating ISO 21287 compact air cylinder with a Ø32mm bore and 65mm stroke, 1/8" air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder. Twin guide rods keep the tooling from rotating.
- BoreØ32 mm
- Stroke65 mm
- Port size1/8"
- Acting typeDouble acting, non-rotating
- Rod threadM8×1.25
- CushionFixed TPU bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac TACE Guided Compact Cylinder TACE32X65S
The AirTAC TACE32X65S is a double acting, non-rotating ISO 21287 compact cylinder with a 32 mm bore and 65 mm stroke. Twin guide rods on a yoke stop the tooling rotating and carry side load, so a gripper or plate stays square without an external guide. At 0.5 MPa it pushes 402.1 N and pulls 345.6 N; at 0.7 MPa those figures rise to 563 N and 483.8 N. The hard-anodized aluminium body carries an S45C hard-chrome plated rod with a female M8x1.25 thread, and the air ports are 1/8" PT.
Plan on roughly 241 N of usable push at 0.5 MPa (about 0.6 of the rated figure), which lifts about 20 kg vertically with a 2:1 margin. The short ISO 21287 body saves about 50% of the mounting length of an ISO 15552 profile cylinder, so it slots into tight jigs, guards and gantries. This model carries the optional -S magnet, so CMSE or DMSE reed and solid-state switches can be mounted in the body slots. A fixed TPU bumper at each end absorbs end-of-stroke energy; speed runs 30-500 mm/s at 0.15-1.0 MPa (22-145 psi).
Airtac TACE Guided Compact Cylinder TACE32X65S Technical Specifications
| Model | Airtac TACE Guided Compact Cylinder TACE32X65S |
|---|---|
| Series | TACE compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø32 mm |
| Stroke | 65 mm |
| Acting type | Double acting, non-rotating |
| Port size | 1/8" |
| Rod thread | M8×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating; guide rods: stainless steel (Ø12-40) / S45C (larger). Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
Theoretical Output Force (Ø32mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 402 N | 346 N |
| 0.7 MPa | 563 N | 484 N |
| Max (@1.0 MPa) | 82 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin. Twin guide rods stop the tooling rotating.
Model Code: Airtac TACE Guided Compact Cylinder TACE32X65S
| TACE | ISO 21287 compact cylinder (non-rotating (twin-guide yoke)). |
|---|---|
| 32 | Bore size in mm. |
| ×65 | Stroke length in mm. |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Where the Airtac TACE Guided Compact Cylinder TACE32X65S Is Used
PCB test gantry pick-and-place
The 65 mm stroke reaches into a test nest while the twin-guide yoke keeps the gripper square over the board; 402.1 N push at 0.5 MPa handles the clamp with margin to spare.
Carton flap press on a packaging line
A short body matters here - it saves about 50% of the mounting length of an ISO 15552 profile cylinder, tucking under a low guard while delivering 241 N of practical press force.
Reject gate on a bottling conveyor
The non-rotating twin guide rods keep the gate plate from twisting under side load, and the -S magnet with a DMSE switch confirms every extend and retract cycle.
Is the Airtac TACE Guided Compact Cylinder TACE32X65S the Right Cylinder?
Size both ways before committing: at 0.5 MPa the next bore down, 25 mm, delivers 245.4 N push, while 40 mm gives 628.3 N - choose the 32 mm when your load sits between those classes. If the load must stay put when air is lost, add a rod lock or pilot check valve, because the piston will drift. Mount with FB flange, CA/CB clevis, CR or FTC, and pick this -S version when CMSE / DMSE switch feedback on extend and retract is part of the controls plan.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Short stroke fits the compact body
- ✓ Port/thread type (PT / G)
- ✓ Add -S if you need the magnet for sensors
- ✓ Rod type (female / male B) & mount (FA/LB/CA)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Compact body: keep the stroke short and avoid side load on the rod.
- check Do not dismantle the threaded front/back covers.
- check Keep speed within the rated range; the TPU bumper absorbs stroke-end energy.
- check Installation by qualified personnel per AirTAC docs.
Airtac TACE Guided Compact Cylinder TACE32X65S FAQ
At 0.5 MPa the 32 mm bore pushes 402.1 N and pulls 345.6 N. At 0.7 MPa push rises to 563 N and pull to 483.8 N. The theoretical maximum at 1.0 MPa is 82 kgf. For real work, size around 241 N (about 0.6 of the push figure), which lifts roughly 20 kg vertically with a 2:1 margin.
The ISO 21287 short body saves about 50% of the mounting length of an ISO 15552 profile cylinder, and a fixed TPU bumper at each end absorbs end-of-stroke energy. This TACE32X65S carries the optional -S magnet, so CMSE or DMSE reed or solid-state switches mount in the body slots to signal extend and retract. Operating pressure is 0.15-1.0 MPa (22-145 psi); the piston does not hold position when air is lost, so use a rod lock or pilot check valve for a held load.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac TACE Guided Compact Cylinder TACE32X65S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.