Airtac TACE Guided Compact Cylinder TACE80X15
The AirTAC Airtac TACE Guided Compact Cylinder TACE80X15 is a genuine double acting, non-rotating ISO 21287 compact air cylinder with a Ø80mm bore and 15mm stroke, 1/4" air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder. Twin guide rods keep the tooling from rotating.
- BoreØ80 mm
- Stroke15 mm
- Port size1/4"
- Acting typeDouble acting, non-rotating
- Rod threadM12×1.75
- CushionFixed TPU bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac TACE Guided Compact Cylinder TACE80X15
A double acting, non-rotating compact cylinder, the AirTAC TACE80X15 pairs an 80 mm bore with a short 15 mm stroke and pushes 2513.3 N at 0.5 MPa (2356.2 N on retraction). Twin guide rods on a yoke stop the tooling rotating and carry side load, so a gripper or press plate stays square without an external guide. At 0.7 MPa the same bore reaches 3518.6 N push and 3298.7 N pull, with a theoretical ceiling of 512.6 kgf at 1.0 MPa.
The ISO 21287 short body saves about 50% of the mounting length of an ISO 15552 profile cylinder, so it slots into tight press fixtures and gantries where a full-length cylinder will not fit. Plan for roughly 1508 N of usable push at 0.5 MPa - about 154 kg of real work - or count on lifting about 128 kg vertically with a 2:1 margin. A fixed TPU bumper absorbs end-of-stroke energy, while the hard-anodized aluminium body and S45C hard-chrome rod take the wear.
Airtac TACE Guided Compact Cylinder TACE80X15 Technical Specifications
| Model | Airtac TACE Guided Compact Cylinder TACE80X15 |
|---|---|
| Series | TACE compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø80 mm |
| Stroke | 15 mm |
| Acting type | Double acting, non-rotating |
| Port size | 1/4" |
| Rod thread | M12×1.75 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating; guide rods: stainless steel (Ø12-40) / S45C (larger). Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
Theoretical Output Force (Ø80mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 2513 N | 2356 N |
| 0.7 MPa | 3519 N | 3299 N |
| Max (@1.0 MPa) | 513 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin. Twin guide rods stop the tooling rotating.
Model Code: Airtac TACE Guided Compact Cylinder TACE80X15
| TACE | ISO 21287 compact cylinder (non-rotating (twin-guide yoke)). |
|---|---|
| 80 | Bore size in mm. |
| ×15 | Stroke length in mm. |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Where the Airtac TACE Guided Compact Cylinder TACE80X15 Is Used
Short-stroke marking press
Stamps batch codes into aluminium extrusions with 2513.3 N at 0.5 MPa; the 15 mm stroke and short ISO 21287 body fit inside a tight press head.
Gearbox housing clamp
Clamps a cast housing on a machining fixture; the twin-guide yoke keeps the clamp pad square and carries side load without an external guide.
Die ejector on a stamping line
Ejects finished brackets off the die face in one quick 15 mm hit; the fixed TPU bumper absorbs the end-of-stroke shock at up to 500 mm/s.
Is the Airtac TACE Guided Compact Cylinder TACE80X15 the Right Cylinder?
For a 15 mm stroke pushing near 2500 N, this 80 mm bore is the match; step down to a 63 mm bore (1558.6 N push at 0.5 MPa) if the load is lighter, or up to a 100 mm bore (3927.0 N) for heavier press work. Air pressure runs 0.15-1.0 MPa (22-145 psi) and speed 30-500 mm/s. The piston drifts when air is lost, so add a rod lock or pilot check valve if the load must stay put. Mount with FB flange, CA/CB clevis, CR or FTC; order the optional -S magnet if CMSE / DMSE switches are planned. Port is 1/4" and the rod end is female M12x1.75.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Short stroke fits the compact body
- ✓ Port/thread type (PT / G)
- ✓ Add -S if you need the magnet for sensors
- ✓ Rod type (female / male B) & mount (FA/LB/CA)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Compact body: keep the stroke short and avoid side load on the rod.
- check Do not dismantle the threaded front/back covers.
- check Keep speed within the rated range; the TPU bumper absorbs stroke-end energy.
- check Installation by qualified personnel per AirTAC docs.
Airtac TACE Guided Compact Cylinder TACE80X15 FAQ
At 0.5 MPa it pushes 2513.3 N and pulls 2356.2 N; at 0.7 MPa it pushes 3518.6 N and pulls 3298.7 N, with a theoretical maximum of 512.6 kgf at 1.0 MPa. Operating pressure is 0.15-1.0 MPa (22-145 psi), proof pressure 1.5 MPa (215 psi), air filtered to 40 um, speed 30-500 mm/s, temperature -20 to +70 C. The port is 1/4" PT and the rod end carries a female M12x1.75 thread.
The ISO 21287 short body saves about 50% of the mounting length of an ISO 15552 profile cylinder, with a fixed TPU bumper at both ends and FB, CA, CB, CR or FTC mounting options. Sensing requires the optional -S magnet code; once ordered, CMSE / DMSE switches detect end positions on the body's magnet slots. Without -S there is no magnet, so no switch can be mounted.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac TACE Guided Compact Cylinder TACE80X15
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.