Airtac TACE Guided Compact Cylinder TACE80X25S
The AirTAC Airtac TACE Guided Compact Cylinder TACE80X25S is a genuine double acting, non-rotating ISO 21287 compact air cylinder with a Ø80mm bore and 25mm stroke, 1/4" air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder. Twin guide rods keep the tooling from rotating.
- BoreØ80 mm
- Stroke25 mm
- Port size1/4"
- Acting typeDouble acting, non-rotating
- Rod threadM12×1.75
- CushionFixed TPU bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac TACE Guided Compact Cylinder TACE80X25S
Double acting and non-rotating, the AirTAC TACE80X25S delivers 2513.3 N push and 2356.2 N pull at 0.5 MPa from an 80 mm bore over a short 25 mm stroke. Twin guide rods on a yoke stop the tooling rotating and carry side load, so a heavy gripper plate stays square without an external guide. The hard-anodized aluminium body takes a 1/4" PT port, and the 20 mm S45C hard-chrome rod ends in a female M12x1.75 thread.
Plan on about 1508 N of real work at 0.5 MPa - roughly 60% of the push rating - which lifts about 128 kg vertically with a 2:1 margin. The short ISO 21287 body saves about 50% of the mounting length of an ISO 15552 profile cylinder, so it slots into tight press fixtures and guarded gantries where a full-length cylinder will not. This model carries the -S magnet, so CMSE / DMSE switches can be mounted for end-of-stroke sensing, and a fixed TPU bumper absorbs energy at both ends. Operating range is 0.15-1.0 MPa (22-145 psi) at 30-500 mm/s.
Airtac TACE Guided Compact Cylinder TACE80X25S Technical Specifications
| Model | Airtac TACE Guided Compact Cylinder TACE80X25S |
|---|---|
| Series | TACE compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø80 mm |
| Stroke | 25 mm |
| Acting type | Double acting, non-rotating |
| Port size | 1/4" |
| Rod thread | M12×1.75 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating; guide rods: stainless steel (Ø12-40) / S45C (larger). Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
Theoretical Output Force (Ø80mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 2513 N | 2356 N |
| 0.7 MPa | 3519 N | 3299 N |
| Max (@1.0 MPa) | 513 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin. Twin guide rods stop the tooling rotating.
Model Code: Airtac TACE Guided Compact Cylinder TACE80X25S
| TACE | ISO 21287 compact cylinder (non-rotating (twin-guide yoke)). |
|---|---|
| 80 | Bore size in mm. |
| ×25 | Stroke length in mm. |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Where the Airtac TACE Guided Compact Cylinder TACE80X25S Is Used
Press-fit staking station
A 25 mm stroke is enough to stake bushings into automotive bracket bosses; 2513.3 N at 0.5 MPa seats parts without dedicating a full-size press.
CNC fixture clamping
Clamps a cast-iron housing against hard stops on a machining pallet; the twin-guide yoke keeps the clamp plate square under side load.
Heavy gate diverting
Kicks heavy aluminium die castings between conveyor lanes; the short ISO 21287 body fits under low guarding where a longer cylinder will not.
Is the Airtac TACE Guided Compact Cylinder TACE80X25S the Right Cylinder?
At 80 mm bore this sits near the top of the ACE range: a 63 mm bore pushes 1558.6 N at 0.5 MPa, while a 100 mm bore reaches 3927.0 N, so step down or up to match the load. The piston drifts if air is lost, so add a rod lock or pilot check valve wherever a held load matters. Mounting choices are FB flange, CA/CB clevis, CR and FTC; the -S magnet fitted to this model pairs with CMSE / DMSE switches, and strokes up to 300 mm are standard for this bore.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Short stroke fits the compact body
- ✓ Port/thread type (PT / G)
- ✓ Add -S if you need the magnet for sensors
- ✓ Rod type (female / male B) & mount (FA/LB/CA)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Compact body: keep the stroke short and avoid side load on the rod.
- check Do not dismantle the threaded front/back covers.
- check Keep speed within the rated range; the TPU bumper absorbs stroke-end energy.
- check Installation by qualified personnel per AirTAC docs.
Airtac TACE Guided Compact Cylinder TACE80X25S FAQ
At 0.5 MPa it pushes 2513.3 N and pulls 2356.2 N; at 0.7 MPa those rise to 3518.6 N push and 3298.7 N pull. The theoretical maximum is 512.6 kgf at 1.0 MPa. Air must be filtered to 40 um, and speed runs 30-500 mm/s across a 0.15-1.0 MPa (22-145 psi) operating band.
The ISO 21287 body is hard-anodized aluminium with threaded aluminium-alloy covers, saving about 50% of the mounting length of an ISO 15552 profile cylinder. A fixed TPU bumper absorbs end-of-stroke energy at both ends. FB flange, CA/CB clevis, CR and FTC mountings fit, and because this model carries the optional -S magnet, CMSE / DMSE reed or solid-state switches can be mounted directly on the body.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac TACE Guided Compact Cylinder TACE80X25S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.