Airtac TACE Guided Compact Cylinder TACE80X50S
The AirTAC Airtac TACE Guided Compact Cylinder TACE80X50S is a genuine double acting, non-rotating ISO 21287 compact air cylinder with a Ø80mm bore and 50mm stroke, 1/4" air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder. Twin guide rods keep the tooling from rotating.
- BoreØ80 mm
- Stroke50 mm
- Port size1/4"
- Acting typeDouble acting, non-rotating
- Rod threadM12×1.75
- CushionFixed TPU bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac TACE Guided Compact Cylinder TACE80X50S
Built as a double acting, non-rotating compact cylinder to ISO 21287, the TACE80X50S uses an 80 mm bore to drive a 20 mm rod through a 50 mm stroke, pushing 2513.3 N and pulling 2356.2 N at 0.5 MPa (3518.6 N push at 0.7 MPa, with a theoretical maximum of 512.6 kgf at 1.0 MPa). Twin guide rods on a yoke stop the tooling rotating and carry side load, so a gripper or clamping plate stays square without any external guide.
The short ISO 21287 body saves about 50% of the mounting length of an ISO 15552 profile cylinder, so it fits tight presses, guards and gantries. Plan on roughly 1508 N of usable push at 0.5 MPa, which lifts about 128 kg vertically with a 2:1 margin. This -S version carries the optional magnet, so CMSE / DMSE reed or solid-state switches can be mounted; a fixed TPU bumper absorbs end-of-stroke energy and the 1/4" port supports speeds of 30-500 mm/s.
Airtac TACE Guided Compact Cylinder TACE80X50S Technical Specifications
| Model | Airtac TACE Guided Compact Cylinder TACE80X50S |
|---|---|
| Series | TACE compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø80 mm |
| Stroke | 50 mm |
| Acting type | Double acting, non-rotating |
| Port size | 1/4" |
| Rod thread | M12×1.75 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating; guide rods: stainless steel (Ø12-40) / S45C (larger). Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
Theoretical Output Force (Ø80mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 2513 N | 2356 N |
| 0.7 MPa | 3519 N | 3299 N |
| Max (@1.0 MPa) | 513 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin. Twin guide rods stop the tooling rotating.
Model Code: Airtac TACE Guided Compact Cylinder TACE80X50S
| TACE | ISO 21287 compact cylinder (non-rotating (twin-guide yoke)). |
|---|---|
| 80 | Bore size in mm. |
| ×50 | Stroke length in mm. |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Where the Airtac TACE Guided Compact Cylinder TACE80X50S Is Used
Machining fixture clamping
Swing clamps on a CNC fixture get about 2513 N of hold-down at 0.5 MPa, enough to lock an aluminium gearbox housing in place through roughing cuts.
Bushing press station
A 50 mm stroke suits a bench press that inserts bushings into pump housings; 3518.6 N at 0.7 MPa covers light interference-fit work.
Gantry part lift
On an assembly gantry the twin-guide yoke lifts a part of about 128 kg vertically with a 2:1 margin, and the guide rods keep the gripper from twisting.
Is the Airtac TACE Guided Compact Cylinder TACE80X50S the Right Cylinder?
For lighter clamping work, the 63 mm bore delivers 1558.6 N push at 0.5 MPa; for heavier press or punch duty, step up to the 100 mm bore at 3927.0 N. If the load must stay put when air is lost, add a rod lock or pilot check valve - the piston will drift otherwise. Mounting options are FB flange, CA/CB clevis, CR and FTC; the rod end is female M12x1.75 and the port thread is PT. The -S magnet on this model is what enables CMSE / DMSE switch mounting.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Short stroke fits the compact body
- ✓ Port/thread type (PT / G)
- ✓ Add -S if you need the magnet for sensors
- ✓ Rod type (female / male B) & mount (FA/LB/CA)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Compact body: keep the stroke short and avoid side load on the rod.
- check Do not dismantle the threaded front/back covers.
- check Keep speed within the rated range; the TPU bumper absorbs stroke-end energy.
- check Installation by qualified personnel per AirTAC docs.
Airtac TACE Guided Compact Cylinder TACE80X50S FAQ
At 0.5 MPa it pushes 2513.3 N and pulls 2356.2 N; at 0.7 MPa it pushes 3518.6 N and pulls 3298.7 N. The theoretical maximum is 512.6 kgf at 1.0 MPa. Operating pressure is 0.15-1.0 MPa (22-145 psi) with a 1.5 MPa (215 psi) proof pressure, and the 80 mm bore breathes through a 1/4" PT port.
It is an ISO 21287 compact cylinder whose short body saves about 50% of the mounting length of an ISO 15552 profile cylinder. The hard-anodized aluminium body carries an S45C hard-chrome-plated rod, with a fixed TPU bumper at both ends and FB, CA/CB, CR or FTC mounting. This -S model includes the optional magnet, so CMSE / DMSE reed or solid-state switches can be mounted directly on the body.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac TACE Guided Compact Cylinder TACE80X50S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.