Airtac TACE Guided Compact Cylinder TACE80X60
The AirTAC Airtac TACE Guided Compact Cylinder TACE80X60 is a genuine double acting, non-rotating ISO 21287 compact air cylinder with a Ø80mm bore and 60mm stroke, 1/4" air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder. Twin guide rods keep the tooling from rotating.
- BoreØ80 mm
- Stroke60 mm
- Port size1/4"
- Acting typeDouble acting, non-rotating
- Rod threadM12×1.75
- CushionFixed TPU bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac TACE Guided Compact Cylinder TACE80X60
Double acting and non-rotating, the TACE80X60 pairs an 80 mm bore with a 60 mm stroke and pushes 2513.3 N at 0.5 MPa (3518.6 N at 0.7 MPa). Twin guide rods on a yoke stop the tooling rotating and carry side load, so a gripper or press plate stays square without an external guide. The hard-anodized aluminium body carries an S45C carbon-steel piston rod with hard-chrome plating, 20 mm across, and a fixed TPU bumper at each end absorbs end-of-stroke energy.
At 0.5 MPa you can plan on roughly 1508 N of real work from the 2513.3 N push rating, which translates to lifting about 128 kg vertically with a 2:1 margin. The short ISO 21287 body saves about 50% of the mounting length of an ISO 15552 profile cylinder, so it drops into press frames and gantries where a full-length cylinder will not fit. Air supply is 0.15-1.0 MPa (22-145 psi), speed 30-500 mm/s, port 1/4". The magnet is optional: order the -S code to enable CMSE / DMSE switches, as this base model carries no magnet.
Airtac TACE Guided Compact Cylinder TACE80X60 Technical Specifications
| Model | Airtac TACE Guided Compact Cylinder TACE80X60 |
|---|---|
| Series | TACE compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø80 mm |
| Stroke | 60 mm |
| Acting type | Double acting, non-rotating |
| Port size | 1/4" |
| Rod thread | M12×1.75 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating; guide rods: stainless steel (Ø12-40) / S45C (larger). Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
Theoretical Output Force (Ø80mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 2513 N | 2356 N |
| 0.7 MPa | 3519 N | 3299 N |
| Max (@1.0 MPa) | 513 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin. Twin guide rods stop the tooling rotating.
Model Code: Airtac TACE Guided Compact Cylinder TACE80X60
| TACE | ISO 21287 compact cylinder (non-rotating (twin-guide yoke)). |
|---|---|
| 80 | Bore size in mm. |
| ×60 | Stroke length in mm. |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Where the Airtac TACE Guided Compact Cylinder TACE80X60 Is Used
Bearing staking press
A 60 mm stroke is enough to stake ball bearings into electric-motor housings on an automotive subassembly line, with the 2513.3 N push at 0.5 MPa covering typical staking loads.
CNC fixture clamping
Clamps aluminium gearbox castings during a milling operation; the twin-guide yoke keeps the clamp plate square to the fixture even under side load from the cutter.
Heavy tote divert pusher
Pushes loaded plastic totes off a warehouse conveyor into a lane, using about 1508 N of usable force at 0.5 MPa without needing an external guide for the pusher plate.
Is the Airtac TACE Guided Compact Cylinder TACE80X60 the Right Cylinder?
Sizing down, the TACE63X60 pushes 1558.6 N at 0.5 MPa; sizing up, the TACE100X60 reaches 3927.0 N. This 80 mm bore sits between them at 2513.3 N push and 2356.2 N pull. Note that it will not hold position when air is lost, the piston simply drifts, so add a rod lock or pilot check valve where a clamped part must stay put. Mounting choices are FB flange, CA/CB clevis, CR and FTC, and the rod ends in a female M12x1.75 thread. If your PLC needs end-of-stroke signals, order the -S variant so CMSE / DMSE switches can ride the body.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Short stroke fits the compact body
- ✓ Port/thread type (PT / G)
- ✓ Add -S if you need the magnet for sensors
- ✓ Rod type (female / male B) & mount (FA/LB/CA)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Compact body: keep the stroke short and avoid side load on the rod.
- check Do not dismantle the threaded front/back covers.
- check Keep speed within the rated range; the TPU bumper absorbs stroke-end energy.
- check Installation by qualified personnel per AirTAC docs.
Airtac TACE Guided Compact Cylinder TACE80X60 FAQ
At 0.5 MPa it pushes 2513.3 N and pulls 2356.2 N; at 0.7 MPa those figures rise to 3518.6 N push and 3298.7 N pull. The theoretical maximum is 512.6 kgf at 1.0 MPa. Operating pressure is 0.15-1.0 MPa (22-145 psi) with a 1.5 MPa (215 psi) proof rating, and speed runs 30-500 mm/s.
The ISO 21287 short body saves about 50% of the mounting length of an ISO 15552 profile cylinder, and a fixed TPU bumper at each end decelerates the piston. Mounting options are FB flange, CA/CB clevis, CR and FTC. The magnet is the optional -S code: with it ordered, CMSE / DMSE switches can be fitted; without it, no sensor can be mounted. It does not hold a load when air is lost, so use a rod lock or pilot check valve for that.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac TACE Guided Compact Cylinder TACE80X60
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.