Airtac TACE Guided Compact Cylinder TACE80X75S
The AirTAC Airtac TACE Guided Compact Cylinder TACE80X75S is a genuine double acting, non-rotating ISO 21287 compact air cylinder with a Ø80mm bore and 75mm stroke, 1/4" air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder. Twin guide rods keep the tooling from rotating.
- BoreØ80 mm
- Stroke75 mm
- Port size1/4"
- Acting typeDouble acting, non-rotating
- Rod threadM12×1.75
- CushionFixed TPU bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac TACE Guided Compact Cylinder TACE80X75S
A double acting, non-rotating compact cylinder built to ISO 21287, the TACE80X75S pairs an 80 mm bore with a 75 mm stroke and a 20 mm hard-chrome-plated rod. At 0.5 MPa it pushes 2513.3 N and pulls 2356.2 N; at 0.7 MPa those figures rise to 3518.6 N and 3298.7 N, with a theoretical ceiling of 512.6 kgf at 1.0 MPa. The short hard-anodized aluminium body saves about 50% of the mounting length of an ISO 15552 profile cylinder, so it fits inside tight guarding and gantry frames where a full-length body simply will not go.
Twin guide rods on a yoke stop the tooling rotating and carry side load, so a gripper or press plate stays square without any external guide. Plan on roughly 1508 N of usable force at 0.5 MPa (about 60% of the push rating), which lifts about 128 kg vertically with a 2:1 margin. The -S magnet option is fitted on this model, so CMSE or DMSE reed or solid-state switches can be clipped into the body slots anywhere along the stroke. A fixed TPU bumper at each end absorbs end-of-stroke shock; ports are 1/4" PT and the female rod thread is M12x1.75.
Airtac TACE Guided Compact Cylinder TACE80X75S Technical Specifications
| Model | Airtac TACE Guided Compact Cylinder TACE80X75S |
|---|---|
| Series | TACE compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø80 mm |
| Stroke | 75 mm |
| Acting type | Double acting, non-rotating |
| Port size | 1/4" |
| Rod thread | M12×1.75 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating; guide rods: stainless steel (Ø12-40) / S45C (larger). Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
Theoretical Output Force (Ø80mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 2513 N | 2356 N |
| 0.7 MPa | 3519 N | 3299 N |
| Max (@1.0 MPa) | 513 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin. Twin guide rods stop the tooling rotating.
Model Code: Airtac TACE Guided Compact Cylinder TACE80X75S
| TACE | ISO 21287 compact cylinder (non-rotating (twin-guide yoke)). |
|---|---|
| 80 | Bore size in mm. |
| ×75 | Stroke length in mm. |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Where the Airtac TACE Guided Compact Cylinder TACE80X75S Is Used
Bearing press station
Pressing ball bearings into gearbox housings on an automotive assembly line: 2513.3 N at 0.5 MPa covers the press fit, and the 75 mm stroke handles approach plus insertion in one move.
Fixture clamp on a CNC line
Clamping cast-iron pump housings to a machining fixture: the twin guide yoke keeps the clamp plate square under side load, so the part cannot twist as the clamp closes.
Gantry part lift
Lifting about 128 kg aluminium die castings vertically between pallets with a 2:1 margin: the 75 mm stroke clears a pallet lip, and CMSE switches (enabled by the fitted -S magnet) confirm up and down positions.
Is the Airtac TACE Guided Compact Cylinder TACE80X75S the Right Cylinder?
Sizing down, the 63 mm bore gives 1558.6 N push at 0.5 MPa; sizing up, the 100 mm bore reaches 3927.0 N. This 80 mm model sits between them at 2513.3 N push and 2356.2 N pull, running on 0.15-1.0 MPa (22-145 psi) at 30-500 mm/s. The rod drifts if air is lost, so for a load that must stay put add a rod lock or pilot check valve. FB flange, CA/CB clevis, CR or FTC mountings all suit this bore, and the fitted -S magnet lets CMSE / DMSE switches report end or mid positions.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Short stroke fits the compact body
- ✓ Port/thread type (PT / G)
- ✓ Add -S if you need the magnet for sensors
- ✓ Rod type (female / male B) & mount (FA/LB/CA)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Compact body: keep the stroke short and avoid side load on the rod.
- check Do not dismantle the threaded front/back covers.
- check Keep speed within the rated range; the TPU bumper absorbs stroke-end energy.
- check Installation by qualified personnel per AirTAC docs.
Airtac TACE Guided Compact Cylinder TACE80X75S FAQ
Push is 2513.3 N and pull 2356.2 N at 0.5 MPa; at 0.7 MPa push is 3518.6 N and pull 3298.7 N, with a theoretical maximum of 512.6 kgf at 1.0 MPa. It is double acting and non-rotating, with twin guide rods on a yoke, operating pressure 0.15-1.0 MPa (22-145 psi), proof pressure 1.5 MPa (215 psi), speed 30-500 mm/s and a temperature range of -20 to +70 C. The rod is 20 mm with an M12x1.75 female thread and the port is 1/4" PT.
The ISO 21287 short body saves about 50% of the mounting length of an ISO 15552 profile cylinder, which is why it suits tight jigs and guarding. A fixed TPU bumper at each end absorbs end-of-stroke shock. This model carries the -S magnet option, so CMSE or DMSE reed or solid-state switches can be fitted in the slots around the body; on models ordered without -S there is no magnet. Outline dimensions are not listed here - confirm from datasheet.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac TACE Guided Compact Cylinder TACE80X75S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.