Airtac TACED Guided Compact Cylinder TACED20X10
The AirTAC Airtac TACED Guided Compact Cylinder TACED20X10 is a genuine double acting, double rod, non-rotating ISO 21287 compact air cylinder with a Ø20mm bore and 10mm stroke, M5×0.8 air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder. Twin guide rods keep the tooling from rotating.
- BoreØ20 mm
- Stroke10 mm
- Port sizeM5×0.8
- Acting typeDouble acting, double rod, non-rotating
- Rod threadM6×1.0
- CushionFixed TPU bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac TACED Guided Compact Cylinder TACED20X10
A double acting, double rod ISO 21287 compact cylinder, the TACED20X10 pushes a 10 mm rod out of both covers so the 20 mm bore delivers 117.8 N at 0.5 MPa in each direction - the rod-side area is identical either way. Twin guide rods on the yoke stop the tooling rotating and carry side load, so a small gripper or plate stays square without an external guide. The short body saves about 50% of the mounting length of an ISO 15552 profile cylinder.
For sizing, plan on roughly 70 N (about 7 kgf) of usable push at 0.5 MPa rather than the full 117.8 N rating; vertically that means lifting about 6 kg with a 2:1 margin. The hard-anodized aluminium body pairs with an S45C hard-chrome rod, a fixed TPU bumper absorbs end-of-stroke shock at both ends, and the optional -S magnet enables CMSE / DMSE switches - without -S no magnet is fitted. Speed range is 30-500 mm/s.
Airtac TACED Guided Compact Cylinder TACED20X10 Technical Specifications
| Model | Airtac TACED Guided Compact Cylinder TACED20X10 |
|---|---|
| Series | TACED compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø20 mm |
| Stroke | 10 mm |
| Acting type | Double acting, double rod, non-rotating |
| Port size | M5×0.8 |
| Rod thread | M6×1.0 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating; guide rods: stainless steel (Ø12-40) / S45C (larger). Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
Theoretical Output Force (Ø20mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 118 N |
| 0.7 MPa | 165 N |
| Max (@1.0 MPa) | 24 kgf |
Double-rod: a rod exits both covers, so output force is equal in both directions (rod-side area used). Twin guide rods carry the side load and stop the tooling rotating.
Model Code: Airtac TACED Guided Compact Cylinder TACED20X10
| TACED | ISO 21287 compact cylinder (double-rod non-rotating (twin-guide yoke)). |
|---|---|
| 20 | Bore size in mm. |
| ×10 | Stroke length in mm. |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Where the Airtac TACED Guided Compact Cylinder TACED20X10 Is Used
Small-part gripper on a pick station
The through-rod gives 117.8 N of grip force in both directions at 0.5 MPa, while the twin guide yoke keeps the jaws from twisting on 10 mm moves.
Lab fixture eject pin
A 10 mm stroke is ideal for nudging test coupons off a nest; the compact body fits where an ISO 15552 profile cylinder would be twice as long.
Presence check with position feedback
Order the -S magnet and CMSE / DMSE switches to signal extend and retract on a gauge or go/no-go station running 30-500 mm/s.
Is the Airtac TACED Guided Compact Cylinder TACED20X10 the Right Cylinder?
At 117.8 N per direction at 0.5 MPa, this 20 mm bore sits between the 16 mm (75.4 N) and 25 mm (206.2 N) double-rod units; step up if your clamp needs over about 120 N. The 10 mm stroke suits short-reach eject or gauge moves, and bore 20 accepts strokes to 100 mm as standard. Note it will not hold position if air is lost - add a rod lock or pilot check valve for a held load. Female M6x1.0 rod thread, M5x0.8 port, FB flange mounting, and order the -S code if you need CMSE / DMSE sensing.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Short stroke fits the compact body
- ✓ Port/thread type (PT / G)
- ✓ Add -S if you need the magnet for sensors
- ✓ Rod type (female / male B) & mount (FA/LB/CA)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Compact body: keep the stroke short and avoid side load on the rod.
- check Do not dismantle the threaded front/back covers.
- check Keep speed within the rated range; the TPU bumper absorbs stroke-end energy.
- check Installation by qualified personnel per AirTAC docs.
Airtac TACED Guided Compact Cylinder TACED20X10 FAQ
Because a rod exits both covers, force is equal in both directions: 117.8 N at 0.5 MPa and 164.9 N at 0.7 MPa, with a maximum of 24.0 kgf at 1.0 MPa. Operating pressure is 0.15-1.0 MPa (22-145 psi), proof 1.5 MPa (215 psi), speed 30-500 mm/s, temperature -20 to +70 C, air filtered to 40 um.
It is an ISO 21287 compact cylinder whose short body saves about 50% of the mounting length of an ISO 15552 profile cylinder. A fixed TPU bumper at each end absorbs end-of-stroke energy; it is not adjustable and does not hold or brake a load. FB flange mounting is available, and the optional -S magnet allows CMSE / DMSE switch sensing.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac TACED Guided Compact Cylinder TACED20X10
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.