Airtac TACED Guided Compact Cylinder TACED20X75S
The AirTAC Airtac TACED Guided Compact Cylinder TACED20X75S is a genuine double acting, double rod, non-rotating ISO 21287 compact air cylinder with a Ø20mm bore and 75mm stroke, M5×0.8 air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder. Twin guide rods keep the tooling from rotating.
- BoreØ20 mm
- Stroke75 mm
- Port sizeM5×0.8
- Acting typeDouble acting, double rod, non-rotating
- Rod threadM6×1.0
- CushionFixed TPU bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac TACED Guided Compact Cylinder TACED20X75S
A double acting, double-rod compact cylinder built to ISO 21287, the TACED20X75S pushes a 20 mm bore through a 75 mm stroke with a rod leaving both covers. Because each side sees the rod-side area, output is identical in either direction: 117.8 N at 0.5 MPa and 164.9 N at 0.7 MPa, both ways. Twin guide rods on the yoke stop the tooling rotating and take side load, so a gripper or plate stays square without an external guide. The hard-anodized aluminium body pairs with an S45C hard-chrome plated rod for long service life.
The short ISO 21287 body saves about 50% of the mounting length of an ISO 15552 profile cylinder, so it slots into tight jigs, guards and gantries. A fixed TPU bumper at each end absorbs end-of-stroke energy, and the -S magnet this model carries accepts CMSE / DMSE reed or solid-state switches for position feedback. Running 0.15-1.0 MPa (22-145 psi) at 30-500 mm/s, it delivers about 70 N of usable work at 0.5 MPa, which lifts roughly 6 kg vertically with a 2:1 margin.
Airtac TACED Guided Compact Cylinder TACED20X75S Technical Specifications
| Model | Airtac TACED Guided Compact Cylinder TACED20X75S |
|---|---|
| Series | TACED compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø20 mm |
| Stroke | 75 mm |
| Acting type | Double acting, double rod, non-rotating |
| Port size | M5×0.8 |
| Rod thread | M6×1.0 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating; guide rods: stainless steel (Ø12-40) / S45C (larger). Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
Theoretical Output Force (Ø20mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 118 N |
| 0.7 MPa | 165 N |
| Max (@1.0 MPa) | 24 kgf |
Double-rod: a rod exits both covers, so output force is equal in both directions (rod-side area used). Twin guide rods carry the side load and stop the tooling rotating.
Model Code: Airtac TACED Guided Compact Cylinder TACED20X75S
| TACED | ISO 21287 compact cylinder (double-rod non-rotating (twin-guide yoke)). |
|---|---|
| 20 | Bore size in mm. |
| ×75 | Stroke length in mm. |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Where the Airtac TACED Guided Compact Cylinder TACED20X75S Is Used
Push-pull fixture clamping
Equal 117.8 N force in both directions lets one cylinder clamp and release a machining fixture without reversing ports or adding a second actuator.
Bidirectional part transfer
On a small electronics assembly line, the through-rod pushes trays left or right with identical force, while the twin guide yoke keeps the pusher plate square.
Position-monitored test station
The fitted -S magnet drives CMSE / DMSE switches so a QC bench confirms end-of-stroke reach on each 75 mm test cycle at 30-500 mm/s.
Is the Airtac TACED Guided Compact Cylinder TACED20X75S the Right Cylinder?
At 117.8 N per side at 0.5 MPa, the 20 mm bore suits light clamping and transfer tasks; step down to the 16 mm bore (75.4 N) for smaller loads or up to the 25 mm bore (206.2 N) when more force is needed. The 75 mm stroke sits inside the 100 mm standard limit for this bore, so no made-to-order stroke applies. The female M6x1.0 rod thread on both ends and the M5x0.8 port keep plumbing simple; FB flange mounting is available. Note the load drifts if air is lost, so add a rod lock or pilot check valve where a held position matters. The -S magnet is already fitted on this model for CMSE / DMSE switch mounting.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Short stroke fits the compact body
- ✓ Port/thread type (PT / G)
- ✓ Add -S if you need the magnet for sensors
- ✓ Rod type (female / male B) & mount (FA/LB/CA)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Compact body: keep the stroke short and avoid side load on the rod.
- check Do not dismantle the threaded front/back covers.
- check Keep speed within the rated range; the TPU bumper absorbs stroke-end energy.
- check Installation by qualified personnel per AirTAC docs.
Airtac TACED Guided Compact Cylinder TACED20X75S FAQ
Yes. As a double-rod cylinder, the rod-side area works on both sides, so output is equal either way: 117.8 N at 0.5 MPa and 164.9 N at 0.7 MPa, with a maximum of 24.0 kgf at 1.0 MPa. In practice plan on about 70 N of real work at 0.5 MPa, roughly a 6 kg vertical lift with a 2:1 margin.
The ISO 21287 short body saves about 50% of the mounting length of an ISO 15552 profile cylinder, ideal for tight gantries. The -S code on this model means the magnet is fitted, so CMSE / DMSE reed or solid-state switches can be mounted in the body slots. A fixed TPU bumper at each end absorbs stroke-end impact, and FB flange mounting is offered.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac TACED Guided Compact Cylinder TACED20X75S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.