Airtac TN Double Axis Double Rod Cylinder TN10X10SH
The AirTAC Airtac TN Double Axis Double Rod Cylinder TN10X10SH is a genuine TN twin-rod (double-rod) double-acting cylinder, 10 mm bore. Two parallel rods on one plate resist bending and twisting and let the load mount without rotating. It delivers about 78.6 N of push at 0.5 MPa. A front bumper cushions the impact and adjusts the stroke over a -5 to 0 mm range.
- TypeTwin-rod, double acting
- Standardenterprise standard
- Bore10 mm
- Push thrust @0.5 MPa78.6 N
- Operating pressure0.2 - 1.0 MPa (29 - 145 psi)
- Port sizeM5x0.8
- CushionAdjustable bumper (-5 to 0 mm)
- MagnetStandard (sensor-ready)
- ThreadPT
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac TN Double Axis Double Rod Cylinder TN10X10SH
The TN10X10SH is a double-acting twin-rod cylinder: two pistons drive two parallel rods fixed to one shared plate, so the plate carries the load without rotating and resists bending and twisting. With a 10 mm bore and a short 10 mm stroke it delivers about 78.5 N of push thrust at 0.5 MPa, and the external bumper at the front both cushions impact and adjusts the effective stroke over -5 to 0 mm.
This is a genuine AirTAC part built to the enterprise-standard TN specification with PT thread ports. A position-detection magnet is fitted as standard on every TN cylinder, with magnetic-switch slots around the body. We confirm exact dimensions and sizing from the datasheet on request.
Airtac TN Double Axis Double Rod Cylinder TN10X10SH Technical Specifications
| Model | Airtac TN Double Axis Double Rod Cylinder TN10X10SH |
|---|---|
| Type | Twin-rod cylinder, double acting |
| Series / standard | TN (enterprise standard) |
| Bore | 10 mm |
| Push thrust @0.5 MPa | 78.6 N |
| Port size | M5x0.8 (PT thread) |
| Fluid | Air, filtered to 40 um |
|---|---|
| Operating pressure | 0.2 - 1.0 MPa (29 - 145 psi) |
| Proof pressure | 1.5 MPa (215 psi) |
| Temperature | -20 to 70 C |
| Speed range | 30 - 500 mm/s |
| Cushion | Bumper, stroke adjustable -5 to 0 mm |
| Magnet | Standard (magnetic-switch slots around the body) |
Specifications follow the official AirTAC TN/TR twin-rod data. Operating pressure is set by bore (0.2 MPa minimum on the 6 and 10 mm bores). The front cover and piston are short, so avoid an over-long stroke. Overall dimensions vary per stroke and allowable side-load is published as curves — ask us and we confirm from the datasheet.
How to choose
Bore sets the thrust: this 10 mm bore gives about 78.5 N push at 0.5 MPa and runs at 0.2-1.0 MPa; step up to 16/20/25/32 mm bores when you need more force. TN is the enterprise-standard series with PT thread only - the JIS-standard TR series is the choice for G or NPT thread and higher non-rotating precision. Strokes are selected from the bore's table; on a 10 mm stroke, allow for the bumper's -5 to 0 mm trim when checking cover clearance. Side-load figures are published as curves, so route those checks to us for confirmation from the datasheet.
Applications
Machine gate stopper
The plate extends square into a part flow to act as a positive stop at a workstation, holding position without rotating.
Locate-and-clamp
Twin rods seat and clamp a small component in a drill or press fixture; the shared plate keeps the clamp face parallel to the part.
Compact press head
A short-stroke press or crimp head mounted on the plate stays level through the 10 mm working stroke under light load.
FAQ
How do I choose between the TN10X10SH and a TR twin-rod cylinder?
TN is the enterprise-standard series with PT thread only. If you need G or NPT thread options, higher non-rotating accuracy, low rod-end deflection, or two groups of ports on both sides, choose the JIS-standard TR series.
Can the TN10X10SH take a side load on the plate?
The twin-rod design resists bending and twisting, but allowable side-load and rod-end deflection are published only as curves, not single numbers. Confirm the applicable figures with us from the datasheet before mounting the load.