Airtac TN Double Axis Double Rod Cylinder TN25X100SH
The AirTAC Airtac TN Double Axis Double Rod Cylinder TN25X100SH is a genuine TN twin-rod (double-rod) double-acting cylinder, 25 mm bore. Two parallel rods on one plate resist bending and twisting and let the load mount without rotating. It delivers about 490.9 N of push at 0.5 MPa. A front bumper cushions the impact and adjusts the stroke over a -5 to 0 mm range.
- TypeTwin-rod, double acting
- Standardenterprise standard
- Bore25 mm
- Push thrust @0.5 MPa490.9 N
- Operating pressure0.15 - 1.0 MPa (22 - 145 psi)
- Port sizeM5x0.8
- CushionAdjustable bumper (-5 to 0 mm)
- MagnetStandard (sensor-ready)
- ThreadPT
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac TN Double Axis Double Rod Cylinder TN25X100SH
The TN25X100SH is a double-acting twin-rod cylinder: two parallel rods share one plate, so the mounted load resists bending and twisting and travels without rotating. With a 25mm bore and a 100mm stroke, it gives a theoretical push thrust of 245.4 N at 0.5 MPa, enough for steady push, clamp and lift duties on a 100mm travel. A front bumper pad both cushions impact and adjusts the effective stroke over -5 to 0 mm, so end-of-stroke softness and fine positioning come from the same part.
This is a genuine AirTAC part built to the ENTERPRISE-standard TN series, with PT thread ports, an operating pressure of 0.15-1.0 MPa (22-145 psi) for this bore, and a position-detecting magnet fitted as standard with magnetic-switch slots around the body. It runs on air filtered to 40 um at 30-500 mm/s and -20 to 70 C. We confirm overall dimensions and sizing from the datasheet on request.
Airtac TN Double Axis Double Rod Cylinder TN25X100SH Technical Specifications
| Model | Airtac TN Double Axis Double Rod Cylinder TN25X100SH |
|---|---|
| Type | Twin-rod cylinder, double acting |
| Series / standard | TN (enterprise standard) |
| Bore | 25 mm |
| Push thrust @0.5 MPa | 490.9 N |
| Port size | M5x0.8 (PT thread) |
| Fluid | Air, filtered to 40 um |
|---|---|
| Operating pressure | 0.15 - 1.0 MPa (22 - 145 psi) |
| Proof pressure | 1.5 MPa (215 psi) |
| Temperature | -20 to 70 C |
| Speed range | 30 - 500 mm/s |
| Cushion | Bumper, stroke adjustable -5 to 0 mm |
| Magnet | Standard (magnetic-switch slots around the body) |
Specifications follow the official AirTAC TN/TR twin-rod data. Operating pressure is set by bore (0.2 MPa minimum on the 6 and 10 mm bores). The front cover and piston are short, so avoid an over-long stroke. Overall dimensions vary per stroke and allowable side-load is published as curves — ask us and we confirm from the datasheet.
How to choose
Choose the 25mm bore when you need roughly 245.4 N of push thrust at 0.5 MPa; note the push side is always higher than the pull side. Within the twin-rod range, TN is the ENTERPRISE-standard series and is offered with PT thread ports only. If your design needs G or NPT ports, or TR's higher non-rotating precision with a lengthening sliding-support guide and two groups of ports (one on each side), step up to the JIS-standard TR series in the same bore. This 100mm stroke sits within the 25mm-bore stroke table, but respect the short-cover caution against over-long strokes, and route any side-load question to us so we check the published curves.
Applications
Packaging-line pusher
Bolt a product-pushing plate straight onto the twin-rod plate to slide cartons into a lane or case over the 100mm stroke; the two rods keep the plate square with no added guide rails.
Press-fit clamping station
Use the 25mm bore's 245.4 N push thrust at 0.5 MPa to hold a workpiece against a fixture while it is screwed, glued or staked; the plate carries the clamp load without rotating.
Conveyor stopper gate
Raise and lower a stopper blade across a conveyor to queue parts; the twin rods resist the twisting that would rack a blade driven by a single-rod cylinder.
FAQ
What does the TN25X100SH model code decode to?
TN is the ENTERPRISE-standard twin-rod cylinder series, 25 is the bore in mm, 100 is the stroke in mm, and S means the magnet is fitted as standard - there is no non-magnetic option in this series. TN ports are PT thread.
Can the TN25X100SH handle side loads on the plate?
The two parallel rods give strong resistance to bending and twisting, so the load mounts on the plate without rotating. But allowable side-load and rod-end deflection are published only as curves, not as single numbers, so confirm the value for your application from the datasheet or ask us before mounting an offset load.