Airtac TN Double Axis Double Rod Cylinder TN25X120S
The AirTAC Airtac TN Double Axis Double Rod Cylinder TN25X120S is a genuine TN twin-rod (double-rod) double-acting cylinder, 25 mm bore. Two parallel rods on one plate resist bending and twisting and let the load mount without rotating. It delivers about 490.9 N of push at 0.5 MPa. A front bumper cushions the impact and adjusts the stroke over a -5 to 0 mm range.
- TypeTwin-rod, double acting
- Standardenterprise standard
- Bore25 mm
- Push thrust @0.5 MPa490.9 N
- Operating pressure0.15 - 1.0 MPa (22 - 145 psi)
- Port sizeM5x0.8
- CushionAdjustable bumper (-5 to 0 mm)
- MagnetStandard (sensor-ready)
- ThreadPT
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac TN Double Axis Double Rod Cylinder TN25X120S
The TN25X120S is a double-acting twin-rod cylinder: two parallel rods share one mounting plate, so the load rides without rotating and the plate resists bending and twist. With a 25 mm bore and 120 mm stroke it delivers about 490.9 N of push thrust at 0.5 MPa (pull side is lower), which suits medium-duty pushing, clamping and transfer strokes. An external bumper pad at the front both cushions end-of-stroke impact and fine-adjusts the effective stroke over -5 to 0 mm.
This is a genuine AirTAC part built to the TN enterprise standard, with a magnet fitted as standard on every model and magnetic-switch slots around the body for position sensing. Air connection is PT thread via M5x0.8 ports. We confirm exact dimensions and sizing help from the datasheet on request.
Airtac TN Double Axis Double Rod Cylinder TN25X120S Technical Specifications
| Model | Airtac TN Double Axis Double Rod Cylinder TN25X120S |
|---|---|
| Type | Twin-rod cylinder, double acting |
| Series / standard | TN (enterprise standard) |
| Bore | 25 mm |
| Push thrust @0.5 MPa | 490.9 N |
| Port size | M5x0.8 (PT thread) |
| Fluid | Air, filtered to 40 um |
|---|---|
| Operating pressure | 0.15 - 1.0 MPa (22 - 145 psi) |
| Proof pressure | 1.5 MPa (215 psi) |
| Temperature | -20 to 70 C |
| Speed range | 30 - 500 mm/s |
| Cushion | Bumper, stroke adjustable -5 to 0 mm |
| Magnet | Standard (magnetic-switch slots around the body) |
Specifications follow the official AirTAC TN/TR twin-rod data. Operating pressure is set by bore (0.2 MPa minimum on the 6 and 10 mm bores). The front cover and piston are short, so avoid an over-long stroke. Overall dimensions vary per stroke and allowable side-load is published as curves — ask us and we confirm from the datasheet.
How to choose
Bore 25 gives about 490.9 N push at 0.5 MPa (pull side is lower); step up or down within the TN range (10/16/20/25/32) if you need a different thrust. TN is the enterprise-standard twin rod on PT thread only; if you need G or NPT threads or a higher-precision guide with two-sided ports, choose the JIS-standard TR series instead. 120 mm is a valid stroke within this bore's table, but avoid stretching to very long strokes - the short-cover design means long travels deserve a datasheet check. Side-load capacity is published as curves, so route side-load questions to us.
Applications
Conveyor pusher
Mounts directly on the plate as a pusher that kicks cartons off a conveyor line without the plate rotating, with the bumper softening each strike.
Part clamp
The twin rods hold a clamp plate square as it closes on a fixture, so the plate grips flat instead of canting under load.
Small lift table
Two guided rods lift a small lift plate or elevator stage squarely, keeping the carried part level through the 120 mm travel.
FAQ
Is there a non-magnetic version of the TN25X120S?
No choice is needed: the whole TN series comes with a magnet fitted as standard, and magnetic-switch slots run around the body so you can sense position right away.
How much side load can the twin rods take?
The two rods share the load and resist bending and twisting far better than a single rod, but allowable side load is published only as curves, not a single number - send us your load and stroke and we will confirm it from the datasheet.