Airtac TN Double Axis Double Rod Cylinder TN25X50SH
The AirTAC Airtac TN Double Axis Double Rod Cylinder TN25X50SH is a genuine TN twin-rod (double-rod) double-acting cylinder, 25 mm bore. Two parallel rods on one plate resist bending and twisting and let the load mount without rotating. It delivers about 490.9 N of push at 0.5 MPa. A front bumper cushions the impact and adjusts the stroke over a -5 to 0 mm range.
- TypeTwin-rod, double acting
- Standardenterprise standard
- Bore25 mm
- Push thrust @0.5 MPa490.9 N
- Operating pressure0.15 - 1.0 MPa (22 - 145 psi)
- Port sizeM5x0.8
- CushionAdjustable bumper (-5 to 0 mm)
- MagnetStandard (sensor-ready)
- ThreadPT
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac TN Double Axis Double Rod Cylinder TN25X50SH
The TN25X50SH is a double-acting twin-rod cylinder from AirTAC's TN enterprise series: two parallel rods drive a single shared plate that mounts the load directly and will not rotate in use. With a 25 mm bore and 50 mm stroke, it delivers a theoretical push thrust of about 490.9 N per side at 0.5 MPa, with lower force on the pull side. The front bumper both cushions end-of-stroke impact and allows stroke adjustment over -5 to 0 mm.
This is a genuine AirTAC component, magnet-fitted as standard with magnetic-switch slots around the body, and it uses PT threads - the only thread option on the TN series. The medium is air filtered to 40 um, at -20 to 70 C. Dimensions vary with stroke, so confirm the exact overall size and mounting details from the datasheet, or ask us to check sizing for your layout.
Airtac TN Double Axis Double Rod Cylinder TN25X50SH Technical Specifications
| Model | Airtac TN Double Axis Double Rod Cylinder TN25X50SH |
|---|---|
| Type | Twin-rod cylinder, double acting |
| Series / standard | TN (enterprise standard) |
| Bore | 25 mm |
| Push thrust @0.5 MPa | 490.9 N |
| Port size | M5x0.8 (PT thread) |
| Fluid | Air, filtered to 40 um |
|---|---|
| Operating pressure | 0.15 - 1.0 MPa (22 - 145 psi) |
| Proof pressure | 1.5 MPa (215 psi) |
| Temperature | -20 to 70 C |
| Speed range | 30 - 500 mm/s |
| Cushion | Bumper, stroke adjustable -5 to 0 mm |
| Magnet | Standard (magnetic-switch slots around the body) |
Specifications follow the official AirTAC TN/TR twin-rod data. Operating pressure is set by bore (0.2 MPa minimum on the 6 and 10 mm bores). The front cover and piston are short, so avoid an over-long stroke. Overall dimensions vary per stroke and allowable side-load is published as curves — ask us and we confirm from the datasheet.
How to choose
The 25 mm bore is the right pick where you need roughly 490.9 N of push per side at 0.5 MPa; step up or down a bore size if your force demand differs. The 50 mm stroke is a standard point in this bore's table, but keep strokes within the published range - over-long strokes erode lateral rigidity. TN cylinders are PT-thread only and follow the enterprise standard; if your design needs G or NPT ports or TR's precise guide with minimal rod-end deflection, select the JIS-standard TR series. For side-load figures, which are published as curves only, send us the application and we will verify from the datasheet.
Applications
Stopper on an assembly conveyor
The twin-rod plate rises or extends to stop pallets at a workstation; the two rods keep the stop face from cocking under repeated impacts, and the bumper softens each stop.
Hold-down clamp on a drill jig
The wide twin-rod plate presses the workpiece down without rotating, so the clamped part cannot be dragged out of position when the tool breaks through.
Lane diverter for totes in a pick module
The plate pushes totes from a main conveyor into a sorting lane, resisting the twisting that a single-rod pusher would see on an off-center tote.
FAQ
How do I choose between the TN and TR twin-rod series?
TN (this model) is the enterprise-standard series with PT threads only and bores of 10, 16, 20, 25 and 32 mm. TR is the JIS-standard series with PT, G or NPT threads, a 6 mm bore option, and a more precise guide: higher non-rotating accuracy, low rod-end deflection, and a lengthening sliding-support guide that needs no added lubricant. Pick TN for straightforward push, clamp and transfer duty; pick TR when positioning precision matters.
Is the magnet an optional extra on the TN25X50SH?
No. Every TN-series cylinder, including this one, is supplied magnet-fitted as standard, with slots around the body for magnetic switches, so position sensing can be added without a special-order cylinder.