Airtac TN Double Axis Double Rod Cylinder TN32X50SH
The AirTAC Airtac TN Double Axis Double Rod Cylinder TN32X50SH is a genuine TN twin-rod (double-rod) double-acting cylinder, 32 mm bore. Two parallel rods on one plate resist bending and twisting and let the load mount without rotating. It delivers about 804.3 N of push at 0.5 MPa. A front bumper cushions the impact and adjusts the stroke over a -5 to 0 mm range.
- TypeTwin-rod, double acting
- Standardenterprise standard
- Bore32 mm
- Push thrust @0.5 MPa804.3 N
- Operating pressure0.15 - 1.0 MPa (22 - 145 psi)
- Port size1/8"
- CushionAdjustable bumper (-5 to 0 mm)
- MagnetStandard (sensor-ready)
- ThreadPT
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac TN Double Axis Double Rod Cylinder TN32X50SH
The TN32X50SH is a double-acting twin-rod cylinder: two parallel rods carried on one shared plate hold the load level without rotating and resist bending and twisting. With a 32 mm bore it is the largest size in the TN range, and the 50 mm stroke suits short indexing and clamping moves. At 0.5 MPa the push side delivers a theoretical thrust of about 402.1 N (the pull side is lower). An external bumper at the front both cushions end-of-stroke impact and adjusts the effective stroke over -5 to 0 mm.
This is a genuine AirTAC part built to the enterprise-standard TN series, with the magnet fitted as standard and magnetic-switch slots around the body. Ports are PT thread, operating pressure for this bore is 0.15-1.0 MPa (22-145 psi), the medium is air filtered to 40 um, and the working temperature range is -20 to 70 C. We confirm overall dimensions for the 50 mm stroke and sizing details from the datasheet on request.
Airtac TN Double Axis Double Rod Cylinder TN32X50SH Technical Specifications
| Model | Airtac TN Double Axis Double Rod Cylinder TN32X50SH |
|---|---|
| Type | Twin-rod cylinder, double acting |
| Series / standard | TN (enterprise standard) |
| Bore | 32 mm |
| Push thrust @0.5 MPa | 804.3 N |
| Port size | 1/8" (PT thread) |
| Fluid | Air, filtered to 40 um |
|---|---|
| Operating pressure | 0.15 - 1.0 MPa (22 - 145 psi) |
| Proof pressure | 1.5 MPa (215 psi) |
| Temperature | -20 to 70 C |
| Speed range | 30 - 500 mm/s |
| Cushion | Bumper, stroke adjustable -5 to 0 mm |
| Magnet | Standard (magnetic-switch slots around the body) |
Specifications follow the official AirTAC TN/TR twin-rod data. Operating pressure is set by bore (0.2 MPa minimum on the 6 and 10 mm bores). The front cover and piston are short, so avoid an over-long stroke. Overall dimensions vary per stroke and allowable side-load is published as curves — ask us and we confirm from the datasheet.
How to choose
Bore sets the thrust: at 0.5 MPa this 32 mm bore pushes about 402.1 N, the highest in the TN line, so step down to 25 mm if you need less force. TN is the enterprise-standard series and is supplied with PT thread only; if you need G or NPT ports or a higher-precision guide, look at the JIS-standard TR series instead. Keep the stroke within the TN32 bore table - the 50 mm stroke here is a listed length - and be cautious about stretching to very long strokes, where rod deflection grows; route side-load and deflection questions to us and we will check them against the datasheet curves.
Applications
Conveyor pusher
Mounted alongside a conveyor, the twin-rod plate pushes cartons or totes square off the belt. The two rods keep the push face from twisting, so the product is indexed cleanly at each stroke.
Fixture clamp
On a machining or assembly fixture, the 32 mm bore's push thrust clamps the workpiece while the plate presents a flat, non-rotating mounting face for the clamp pad.
Line stopper
Used as a stopper at a pallet station, the cylinder rises and blocks the flow; the shared plate keeps the stop face level under repeated impact, and the bumper cushions each arrival.
FAQ
What does the S in TN32X50SH stand for?
S indicates the position magnet. Every TN-series cylinder is supplied with the magnet fitted as standard - there is no non-magnetic version to choose between. The magnet works with the magnetic-switch slots around the body, so position sensing is simply a case of fitting a suitable switch. Specific sensor part numbers are listed in the AirTAC catalogue.
Do I need a separate guide for my load, or will the twin rods hold it straight?
The two parallel rods on one shared plate give the cylinder its anti-rotation behavior: the mounted load does not spin and the plate resists bending and twisting. That covers most push, clamp and lift jobs. If your application applies a real side load or overhang, ask us - allowable values are published as curves and we will confirm them from the datasheet for your stroke.