Airtac SE32 Standard Cylinder SE32X1000S
The AirTAC Airtac SE32 Standard Cylinder SE32X1000S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø32mm bore and 1000mm stroke, PT1/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
- BoreØ32 mm
- Stroke1000 mm
- Port sizePT1/8
- Acting typeDouble acting
- Rod threadM10×1.25
- CushionAdjustable, 27 mm
About the Airtac SE32 Standard Cylinder SE32X1000S
The AirTAC SE32X1000S is a double-acting single-rod profile cylinder built to ISO 15552 standards, delivering a push force of 402 N at 0.5 MPa. Its square extruded aluminum barrel eliminates external tie rods, yielding a compact body that resists corrosion and mounts flush against machine frames. This design is dimensionally interchangeable with other ISO 15552 cylinders, simplifying retrofits.
Equipped with a built-in magnetic piston (-S), this unit supports AirTAC CMSE reed and DMSE electronic sensors for precise end-position detection. The field-adjustable air cushioning at both ends allows technicians to tune end-of-stroke deceleration via a set screw, softening hard impacts during high-speed travel up to 800 mm/s.
Airtac SE32 Standard Cylinder SE32X1000S Technical Specifications
| Model | Airtac SE32 Standard Cylinder SE32X1000S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø32 mm |
| Stroke | 1000 mm |
| Acting type | Double acting |
| Port size | PT1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø32mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 402 N | 346 N |
| 0.7 MPa | 563 N | — |
| Max (@1.0 MPa) | 82 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE32 Standard Cylinder SE32X1000S
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 32 | Bore size in mm. |
| ×1000 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE32 Standard Cylinder SE32X1000S Is Used
Carton Pusher Diversion
Uses the 1000 mm stroke to push corrugated cartons across a packaging line diverter, relying on the 402 N push force to overcome sliding friction.
Lab Sample Shuttle
Transports test tube racks between analytical stations, using the -S magnet and DMSE electronic sensors to confirm full extension at the 1000 mm limit.
Tote Ejection Gate
Actuates a swinging gate to eject storage totes from flow rack shelving, benefiting from the tie-rod-free profile that prevents snagging on passing containers.
Is the Airtac SE32 Standard Cylinder SE32X1000S the Right Cylinder?
Choosing this 32 mm bore yields 402 N push and 345 N pull at 0.5 MPa. If your application requires less force, the smaller 32 mm is the baseline option, but stepping up to the 40 mm bore increases push to 628 N for heavier loads. This 1000 mm stroke utilizes the maximum standard length for a 32 mm bore.
Because this model features a 1000 mm stroke, the 12 mm rod and M10x1.25 thread face significant bending moments under side loads; an external guide rail is strongly recommended to prevent rod-bearing wear. Note that the adjustable air cushion only decelerates the piston near stroke end and does not hold the load—if air pressure is lost, the piston will drift. For position holding, consider a BSE rod lock variant.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE32 Standard Cylinder SE32X1000S FAQ
At 0.5 MPa, this 32 mm bore cylinder provides 402 N of push force and 345 N of pull force. At 0.7 MPa, the push force is 563 N, with a maximum push capacity of 82 kgf at 1.0 MPa. The operational speed range is 30-800 mm/s.
Yes, the SE32X1000S is dimensionally interchangeable per ISO 15552, meaning it shares standard mounting footprint and port sizes (PT1/8) with other ISO 15552 profile cylinders. You can drop it into existing hardware without major redesigns.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE32 Standard Cylinder SE32X1000S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.