Airtac SE32 Standard Cylinder SE32X100SH
The AirTAC Airtac SE32 Standard Cylinder SE32X100SH is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø32mm bore and 100mm stroke, PT1/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
- BoreØ32 mm
- Stroke100 mm
- Port sizePT1/8
- Acting typeDouble acting
- Rod threadM10×1.25
- CushionAdjustable, 27 mm
About the Airtac SE32 Standard Cylinder SE32X100SH
The AirTAC SE32X100SH is a double-acting single-rod ISO 15552 profile cylinder engineered for high-temperature automation. Built with a 32mm bore and 100mm stroke, it generates 402N of push force at 0.5 MPa and up to 563N at 0.7 MPa. The FKM Viton seal extends the operating temperature range to 150C, making it highly reliable in thermal processing environments.
Its square extruded aluminum barrel eliminates external tie rods, yielding a compact footprint that mounts flush while resisting corrosion. The integrated magnet (-S) directly supports CMSE reed and DMSE electronic sensors for precise end-of-stroke detection. Furthermore, the field-adjustable air cushioning at both ends allows you to tune deceleration and soften hard end stops dynamically.
Airtac SE32 Standard Cylinder SE32X100SH Technical Specifications
| Model | Airtac SE32 Standard Cylinder SE32X100SH |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø32 mm |
| Stroke | 100 mm |
| Acting type | Double acting |
| Port size | PT1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø32mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 402 N | 346 N |
| 0.7 MPa | 563 N | — |
| Max (@1.0 MPa) | 82 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE32 Standard Cylinder SE32X100SH
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 32 | Bore size in mm. |
| ×100 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE32 Standard Cylinder SE32X100SH Is Used
Injection Mold Ejection
Survives ambient heat near molding lines to deliver 402N of push force for ejecting small plastic parts, with FKM seals resisting thermal degradation.
Heat Shrink Wrapper
Handles the 100mm stroke requirement to index film rolls through shrink-tunnels, where the 150C FKM seal tolerates radiant heat.
Lab Oven Door Actuator
Provides reliable double-acting actuation for small access doors on laboratory ovens, using the -S magnet to trigger DMSE sensors for safe closure.
Is the Airtac SE32 Standard Cylinder SE32X100SH the Right Cylinder?
When sizing this 32mm bore model, note that stepping down is not an option as it is the smallest available SE bore. If your application requires less force, you must rely on a smaller non-ISO series. Conversely, if you need more power, stepping up to the 40mm bore yields 628N of push at 0.5 MPa. As a standard ISO 15552 cylinder, this unit is dimensionally interchangeable with other ISO 15552 profile cylinders, allowing direct retrofitting using existing mounting hardware and PT1/8 ports.
Keep in mind that a plain SE cylinder does not hold its position or load when air is lost or the valve is centered; the piston will drift. If your application must hold a load without live pressure, consider the BSE rod lock variant or an external pilot-operated check valve.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE32 Standard Cylinder SE32X100SH FAQ
The SE32X100SH generates 402N push and 345N pull at 0.5 MPa, 563N push at 0.7 MPa, and a maximum push of 82 kgf at 1.0 MPa. Thanks to the H code FKM Viton seal, it operates in temperatures up to 150C.
Yes. The SE32X100SH is dimensionally interchangeable per ISO 15552 standards. You can drop it directly into existing mounts using its PT1/8 ports and 12mm rod, but never use it as a load-holding brake, as the adjustable air cushion only decelerates the piston near stroke end.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE32 Standard Cylinder SE32X100SH
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.