Airtac SE32 Standard Cylinder SE32X1200S
The AirTAC Airtac SE32 Standard Cylinder SE32X1200S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø32mm bore and 1200mm stroke, PT1/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
- BoreØ32 mm
- Stroke1200 mm
- Port sizePT1/8
- Acting typeDouble acting
- Rod threadM10×1.25
- CushionAdjustable, 27 mm
About the Airtac SE32 Standard Cylinder SE32X1200S
The AirTAC SE32X1200S is a double-acting single-rod ISO 15552 profile cylinder engineered for compact, long-stroke automation. It delivers a 402 N push at 0.5 MPa alongside a 345 N pull, utilizing a 32 mm bore and a 1200 mm stroke. Because this stroke exceeds the 1000 mm standard limit, it is manufactured as a made-to-order unit to exact application lengths.
The extruded aluminum barrel omits external tie rods, yielding a clean profile that mounts flush against frames while resisting corrosion. Integrated -S magnet coding supports AirTAC CMSE reed and DMSE electronic position sensing, while the field-adjustable pneumatic cushioning at both ends lets you dial in end-of-stroke deceleration to prevent hard mechanical impacts.
Airtac SE32 Standard Cylinder SE32X1200S Technical Specifications
| Model | Airtac SE32 Standard Cylinder SE32X1200S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø32 mm |
| Stroke | 1200 mm |
| Acting type | Double acting |
| Port size | PT1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø32mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 402 N | 346 N |
| 0.7 MPa | 563 N | — |
| Max (@1.0 MPa) | 82 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE32 Standard Cylinder SE32X1200S
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 32 | Bore size in mm. |
| ×1200 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE32 Standard Cylinder SE32X1200S Is Used
Packaging Line Diverter
Uses the 1200 mm extended reach to push cartons between parallel packaging lanes, relying on the 402 N push force to overcome friction without crushing the boxes.
Laboratory Sample Shuttle
Moves test racks across long bench stations, using the -S magnet with DMSE electronic sensors to confirm precise sample positioning at each end.
Light-Duty Storage Extractor
Extracts lightweight plastic totes from high-density shelving, where the compact 32 mm profile barrel saves vertical space and the adjustable cushion softens the 800 mm/s transit stop.
Is the Airtac SE32 Standard Cylinder SE32X1200S the Right Cylinder?
Selecting this 32 mm bore makes sense when your application requires the 402 N push at 0.5 MPa but not the heavier footprint of the 40 mm bore, which steps up to 628 N. If your load demands even less force, stepping down is not an option as 32 mm is the smallest available ISO 15552 size in this series. At 1200 mm, this non-standard stroke pushes the 12 mm rod and M10x1.25 thread to their limit; an external guide is strictly recommended to prevent rod-bearing bending and premature seal wear under side loading.
As a true ISO 15552 cylinder, it provides drop-in dimensional interchangeability with other standard profile cylinders, sharing the same mounting interface and PT1/8 port. Remember that a standard SE does not hold position or carry loads if air pressure drops; if your process requires static holding, consider a BSE rod lock variant instead of relying on the air cushion.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE32 Standard Cylinder SE32X1200S FAQ
At 0.5 MPa, this 32 mm bore cylinder provides a 402 N push and a 345 N pull. At 0.7 MPa, the push force is 563 N, and the maximum push is 82 kgf at 1.0 MPa. The operational speed range is 30-800 mm/s.
No. The adjustable air cushion at both ends only decelerates the piston near stroke end and does not act as a brake. If power fails, the rod will drift. For vertical load holding, you need a BSE rod lock variant or an external pilot-operated check valve.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE32 Standard Cylinder SE32X1200S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.