Airtac SE32 Standard Cylinder SE32X125SH
The AirTAC Airtac SE32 Standard Cylinder SE32X125SH is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø32mm bore and 125mm stroke, PT1/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
- BoreØ32 mm
- Stroke125 mm
- Port sizePT1/8
- Acting typeDouble acting
- Rod threadM10×1.25
- CushionAdjustable, 27 mm
About the Airtac SE32 Standard Cylinder SE32X125SH
The AirTAC SE32X125SH is a double-acting, single-rod ISO 15552 profile cylinder engineered for rigorous pneumatic control. It yields 402 N of push force and 345 N of pull force at 0.5 MPa, operating via a PT1/8 port and a 12 mm hard-chrome rod. The square extruded aluminum barrel omits external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machine frames.
This specific configuration integrates an S-coded magnet for CMSE reed and DMSE electronic position sensing, alongside an H-coded FKM seal that elevates the working temperature ceiling to 150 C. Field-adjustable air cushions at both stroke ends allow technicians to tune end-of-stroke deceleration, preventing harsh impacts during high-speed 30-800 mm/s operations.
Airtac SE32 Standard Cylinder SE32X125SH Technical Specifications
| Model | Airtac SE32 Standard Cylinder SE32X125SH |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø32 mm |
| Stroke | 125 mm |
| Acting type | Double acting |
| Port size | PT1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø32mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 402 N | 346 N |
| 0.7 MPa | 563 N | — |
| Max (@1.0 MPa) | 82 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE32 Standard Cylinder SE32X125SH
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 32 | Bore size in mm. |
| ×125 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE32 Standard Cylinder SE32X125SH Is Used
Lab Test Oven Doors
The FKM Viton seals tolerate 150 C ambient heat inside laboratory drying ovens, while the 125 mm stroke provides precise opening and closing of thermal isolation gates.
Small Part Ejection
Delivering 402 N of push force at 0.5 MPa, this cylinder reliably kicks small molded plastic components out of machining centers at speeds up to 800 mm/s.
Sealing Jaw Actuation
The built-in magnet triggers DMSE electronic sensors to verify jaw position on continuous heat-sealing packaging lines before the cycle advances.
Is the Airtac SE32 Standard Cylinder SE32X125SH the Right Cylinder?
If 402 N of push at 0.5 MPa is excessive for your payload, the smaller SE40 bore offers a 628 N alternative, while stepping down is not applicable as 32 mm is the smallest standard SE size. Because this is a standard double-acting cylinder, it will drift and cannot hold a load if air pressure drops or the valve centers; use a BSE rod lock for fail-safe holding. The 125 mm stroke falls under the 300 mm threshold, so standard rod-bearing bending is minimal, though external guides remain best practice for heavy lateral loads. As a dimensionally interchangeable ISO 15552 component, it serves as a direct drop-in replacement for other ISO 15552 cylinders, utilizing the same mounting footprint and PT1/8 porting.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE32 Standard Cylinder SE32X125SH FAQ
The SE32X125SH generates 402 N push and 345 N pull at 0.5 MPa, 563 N push at 0.7 MPa, and a maximum push of 82 kgf at 1.0 MPa. It operates at speeds between 30 and 800 mm/s.
It is dimensionally interchangeable per ISO 15552, serving as a drop-in replacement for other standard profile cylinders. However, it is a standard double-acting cylinder, not a rod lock; it cannot hold a load without live air pressure and will drift if air is lost.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE32 Standard Cylinder SE32X125SH
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.