Airtac SE32 Standard Cylinder SE32X150SH
The AirTAC Airtac SE32 Standard Cylinder SE32X150SH is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø32mm bore and 150mm stroke, PT1/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
- BoreØ32 mm
- Stroke150 mm
- Port sizePT1/8
- Acting typeDouble acting
- Rod threadM10×1.25
- CushionAdjustable, 27 mm
About the Airtac SE32 Standard Cylinder SE32X150SH
The AirTAC SE32X150SH is a double-acting single-rod ISO 15552 profile cylinder engineered for high-temperature actuation. It delivers a 402 N push force at 0.5 MPa, utilizing a 32 mm bore and a 150 mm stroke. Equipped with a Viton (FKM) seal, the operating temperature extends to 150 C, making it suitable for thermal processing environments where standard elastomers fail.
The extruded aluminum barrel omits external tie rods, yielding a compact, corrosion-resistant profile that mounts flush in tight machinery. Field-adjustable air cushions at both ends allow technicians to tune end-of-stroke deceleration, absorbing kinetic energy to prevent hard mechanical impacts. The integrated -S magnet directly interfaces with AirTAC CMSE reed and DMSE electronic sensors for precise position feedback.
Airtac SE32 Standard Cylinder SE32X150SH Technical Specifications
| Model | Airtac SE32 Standard Cylinder SE32X150SH |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø32 mm |
| Stroke | 150 mm |
| Acting type | Double acting |
| Port size | PT1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø32mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 402 N | 346 N |
| 0.7 MPa | 563 N | — |
| Max (@1.0 MPa) | 82 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE32 Standard Cylinder SE32X150SH
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 32 | Bore size in mm. |
| ×150 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE32 Standard Cylinder SE32X150SH Is Used
Lab Oven Door Actuation
The FKM Viton seal withstands 150 C ambient heat inside thermal chambers, while the 402 N push force reliably cycles heavy insulated oven doors.
Plastic Trimming Station
Provides 150 mm travel to actuate a hot-knife cutter for trimming injection-molded plastic sprues, using the integrated magnet for DMSE end-of-stroke verification.
Shrink Wrap Tucking
Drives a 150 mm tucking blade near shrink-tunnel heat tunnels, benefiting from the tie-rod-free extruded profile to fit narrow conveyor side frames.
Is the Airtac SE32 Standard Cylinder SE32X150SH the Right Cylinder?
Delivering 402 N push at 0.5 MPa, this 32 mm bore unit suits light-duty cycling. If your load requires less force, there is no smaller standard ISO 15552 bore, so you must drop to a compact ISO 21287 cylinder. If you need more power, stepping up to the 40 mm bore provides 628 N push. Remember that the adjustable air cushion only decelerates the piston near stroke end; it is not a locking mechanism. If a load must be held without live air pressure, use a BSE rod lock or an external pilot-operated check valve. To retrofit an existing ISO 15552 body, match the 150 mm stroke, PT1/8 port, and add an -S magnet for CMSE/DMSE sensors.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE32 Standard Cylinder SE32X150SH FAQ
At 0.5 MPa, the push force is 402 N and the pull force is 345 N. At 0.7 MPa, the push force is 563 N. The maximum push force is 82 kgf at 1.0 MPa. The operating speed range is 30-800 mm/s.
Yes, it is dimensionally interchangeable per ISO 15552, allowing a drop-in replacement for other standard profile cylinders. The H seal option specifies a Viton (FKM) seal, extending the operating temperature range from -20 C up to 150 C for high-heat environments.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE32 Standard Cylinder SE32X150SH
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.