Airtac SE32 Standard Cylinder SE32X157S
The AirTAC Airtac SE32 Standard Cylinder SE32X157S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø32mm bore and 157mm stroke, PT1/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
- BoreØ32 mm
- Stroke157 mm
- Port sizePT1/8
- Acting typeDouble acting
- Rod threadM10×1.25
- CushionAdjustable, 27 mm
About the Airtac SE32 Standard Cylinder SE32X157S
The AirTAC SE32X157S is a double-acting single-rod profile cylinder built to ISO 15552 dimensions, delivering a 402 N push at 0.5 MPa. Its square extruded aluminum barrel omits external tie rods, yielding a flush, corrosion-resistant body that mounts cleanly in tight machine envelopes.
Equipped with a built-in position magnet (-S), this unit supports AirTAC CMSE reed and DMSE electronic sensors for precise end-of-stroke detection. Field-adjustable air cushioning at both ends allows technicians to tune deceleration and soften hard mechanical impacts at cycle completion.
Airtac SE32 Standard Cylinder SE32X157S Technical Specifications
| Model | Airtac SE32 Standard Cylinder SE32X157S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø32 mm |
| Stroke | 157 mm |
| Acting type | Double acting |
| Port size | PT1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø32mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 402 N | 346 N |
| 0.7 MPa | 563 N | — |
| Max (@1.0 MPa) | 82 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE32 Standard Cylinder SE32X157S
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 32 | Bore size in mm. |
| ×157 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE32 Standard Cylinder SE32X157S Is Used
PCB Drill Bit Changer
Actuates a small tool-change arm in a PCB drilling station, using the 157 mm stroke to swap drill bits with precise magnet-confirmed positioning.
Blister Pack Feed Guide
Pushes thin aluminum blister feed stock into a sealing press, where the 402 N extension force is ample to align the web without crushing it.
Lab Sample Ejection
Ejects processed vial trays from a clinical diagnostic carousel, relying on adjustable end cushions to prevent liquid splashing during rapid 30-800 mm/s cycles.
Is the Airtac SE32 Standard Cylinder SE32X157S the Right Cylinder?
When sizing this 32 mm bore unit, note it yields 402 N push at 0.5 MPa. If your payload requires less energy, there is no smaller standard ISO 15552 bore in this series; stepping up to the 40 mm bore increases output to 628 N. Because the 157 mm stroke is non-standard but within the 1000 mm maximum, it is manufactured to order while retaining standard PT1/8 ports and M10x1.25 rod threads.
For retrofits, this cylinder is dimensionally interchangeable with any ISO 15552 profile cylinder and accepts standard mounting accessories like FA or LB brackets. Remember that a plain double-acting cylinder drifts if air pressure is lost; if the application must hold a vertical load safely during an outage, specify a BSE rod lock variant instead.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE32 Standard Cylinder SE32X157S FAQ
At 0.5 MPa, this 32 mm bore cylinder provides 402 N of push force and 345 N of pull force. At 0.7 MPa, the push increases to 563 N, with a maximum push capability of 82 kgf at 1.0 MPa. The operational speed range is 30-800 mm/s.
Yes, the SE32X157S is dimensionally interchangeable per ISO 15552 standards. You can drop it into existing foot or flange mounting patterns. It features a PT1/8 port and includes a built-in magnet for CMSE and DMSE position sensors.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE32 Standard Cylinder SE32X157S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.