Airtac SE32 Standard Cylinder SE32X165S
The AirTAC Airtac SE32 Standard Cylinder SE32X165S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø32mm bore and 165mm stroke, PT1/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
- BoreØ32 mm
- Stroke165 mm
- Port sizePT1/8
- Acting typeDouble acting
- Rod threadM10×1.25
- CushionAdjustable, 27 mm
About the Airtac SE32 Standard Cylinder SE32X165S
The AirTAC SE32X165S is a double-acting single-rod profile cylinder built to the ISO 15552 standard, delivering a 402 N push at 0.5 MPa. Its 32 mm bore and 165 mm stroke provide a compact footprint for lighter-duty automation. The integrated -S magnet enables direct position sensing using AirTAC CMSE reed or DMSE electronic switches.
This unit uses a square extruded aluminum barrel without external tie rods, allowing flush mounting and high corrosion resistance. The field-adjustable air cushion at both ends lets technicians fine-tune end-of-stroke deceleration to eliminate hard impacts, ensuring smooth operation at speeds up to 800 mm/s.
Airtac SE32 Standard Cylinder SE32X165S Technical Specifications
| Model | Airtac SE32 Standard Cylinder SE32X165S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø32 mm |
| Stroke | 165 mm |
| Acting type | Double acting |
| Port size | PT1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø32mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 402 N | 346 N |
| 0.7 MPa | 563 N | — |
| Max (@1.0 MPa) | 82 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE32 Standard Cylinder SE32X165S
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 32 | Bore size in mm. |
| ×165 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE32 Standard Cylinder SE32X165S Is Used
PCB Depaneling Routing
Provides the precise 402 N push required to drive a routing blade through printed circuit boards without stressing delicate solder joints.
Carton Flap Folding
Uses the 165 mm stroke to extend and fold small corrugated carton flaps at high cycling rates, aided by adjustable end cushions.
Lab Sample Dispensing
Moves reagent trays with smooth, cushioned strokes, relying on the -S magnet to trigger DMSE electronic sensors for exact volumetric metering.
Is the Airtac SE32 Standard Cylinder SE32X165S the Right Cylinder?
If you need slightly less force, the next bore down is 32 mm (this is the smallest size), but stepping up to the 40 mm bore increases the 0.5 MPa push to 628 N. As a 165 mm stroke is a non-standard made-to-order length, expect a slightly longer lead time. Because this stroke exceeds 300 mm, no external side-load guide is strictly required here, but always ensure the 12 mm rod is not subjected to lateral stress.
For drop-in retrofits, this cylinder is dimensionally interchangeable per ISO 15552 with other profile cylinders of the same bore. It uses a PT1/8 port, an M10x1.25 rod thread, and the built-in magnet supports CMSE / DMSE sensors. Remember that the adjustable cushion only decelerates the piston; it does not hold a load if air pressure is lost—use a BSE rod lock for that.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE32 Standard Cylinder SE32X165S FAQ
At 0.5 MPa, the push force is 402 N and the pull force is 345 N. At 0.7 MPa, the push increases to 563 N. The maximum push is 82 kgf at 1.0 MPa, and the operational speed range is 30-800 mm/s.
Yes, the SE32X165S is dimensionally interchangeable per ISO 15552, meaning it shares the exact mounting footprint and interface of other standard 32 mm profile cylinders. It uses a PT1/8 port and an M10x1.25 rod thread.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE32 Standard Cylinder SE32X165S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.