Airtac SE32 Standard Cylinder SE32X180SH
The AirTAC Airtac SE32 Standard Cylinder SE32X180SH is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø32mm bore and 180mm stroke, PT1/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
- BoreØ32 mm
- Stroke180 mm
- Port sizePT1/8
- Acting typeDouble acting
- Rod threadM10×1.25
- CushionAdjustable, 27 mm
About the Airtac SE32 Standard Cylinder SE32X180SH
The AirTAC SE32X180SH is a double-acting, single-rod ISO 15552 profile cylinder with a 32 mm bore and 180 mm stroke. It generates 402 N of push force at 0.5 MPa, making it well-suited for compact, lower-force routing and clamping tasks. The extruded aluminum barrel lacks external tie rods, yielding a clean, corrosion-resistant profile that mounts flush in tight machine envelopes.
This specific configuration includes a built-in magnet (S) for CMSE reed and DMSE electronic position sensing, plus a high-temperature FKM (Viton) seal (H) that extends the operating range up to 150 C. The field-adjustable pneumatic cushioning at both ends allows you to tune end-of-stroke deceleration, protecting tooling during rapid 30-800 mm/s cycles.
Airtac SE32 Standard Cylinder SE32X180SH Technical Specifications
| Model | Airtac SE32 Standard Cylinder SE32X180SH |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø32 mm |
| Stroke | 180 mm |
| Acting type | Double acting |
| Port size | PT1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø32mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 402 N | 346 N |
| 0.7 MPa | 563 N | — |
| Max (@1.0 MPa) | 82 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE32 Standard Cylinder SE32X180SH
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 32 | Bore size in mm. |
| ×180 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE32 Standard Cylinder SE32X180SH Is Used
Lab Sample Handling
The 402 N push force at 0.5 MPa easily moves sample trays, while the FKM Viton seal survives high-temperature sterilization cycles up to 150 C.
PCB Router Clamping
Secures circuit boards during routing with a 180 mm stroke, using the flush extruded profile to fit within dense electronics manufacturing cells.
Film Sealing Jaws
Closes heated sealing jaws rapidly, where the adjustable end cushions soften impacts and the -S magnet triggers DMSE sensors to verify seal completion.
Is the Airtac SE32 Standard Cylinder SE32X180SH the Right Cylinder?
If 402 N of push at 0.5 MPa is insufficient, stepping up to the 40 mm bore yields 628 N. Conversely, if you need a smaller footprint, note that 32 mm is the smallest standard SE bore available. Because this is a 180 mm stroke, the 12 mm rod and M10x1.25 thread handle moderate side loads, but any long unsupported payload should still use an external guide to prevent rod-bearing bending. Remember that a standard double-acting cylinder drifts when air is lost; if you need to hold a load without live pressure, look to the BSE rod lock variant. For drop-in retrofits, match the 32 mm bore, 180 mm stroke, PT1/8 port, and your required mounting accessory.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE32 Standard Cylinder SE32X180SH FAQ
This 32 mm bore cylinder provides 402 N push and 345 N pull at 0.5 MPa, 563 N push at 0.7 MPa, and a maximum push of 82 kgf at 1.0 MPa. It operates at speeds between 30 and 800 mm/s.
Yes, the SE32X180SH is dimensionally interchangeable per ISO 15552, meaning it shares the exact mounting footprint and PT1/8 port locations of other standard profile cylinders. You can drop it directly into existing fixtures.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE32 Standard Cylinder SE32X180SH
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.