Airtac SE32 Standard Cylinder SE32X250SH
The AirTAC Airtac SE32 Standard Cylinder SE32X250SH is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø32mm bore and 250mm stroke, PT1/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
- BoreØ32 mm
- Stroke250 mm
- Port sizePT1/8
- Acting typeDouble acting
- Rod threadM10×1.25
- CushionAdjustable, 27 mm
About the Airtac SE32 Standard Cylinder SE32X250SH
The AirTAC SE32X250SH is a double-acting single-rod ISO 15552 profile cylinder engineered for demanding thermal environments. Delivering 402 N of push force at 0.5 MPa, it features a Viton (FKM) seal that extends the operating temperature range up to 150 C, making it highly reliable in high-heat processing stations.
Its square extruded aluminum barrel eliminates external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machine frames. The integrated -S magnet enables precise position tracking with CMSE reed or DMSE electronic sensors, while field-adjustable air cushions at both ends let you dial in end-of-stroke deceleration to prevent hard impacts.
Airtac SE32 Standard Cylinder SE32X250SH Technical Specifications
| Model | Airtac SE32 Standard Cylinder SE32X250SH |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø32 mm |
| Stroke | 250 mm |
| Acting type | Double acting |
| Port size | PT1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø32mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 402 N | 346 N |
| 0.7 MPa | 563 N | — |
| Max (@1.0 MPa) | 82 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE32 Standard Cylinder SE32X250SH
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 32 | Bore size in mm. |
| ×250 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE32 Standard Cylinder SE32X250SH Is Used
Hot Stamping Ejection
Provides 402 N push at 0.5 MPa to eject small stamped metal parts from heated dies, utilizing the FKM seal to withstand 150 C ambient radiated heat without degrading.
Shrink Wrap Forming
Actuates 250 mm stroke forming jaws on continuous shrink-wrap tunnels, where the Viton seal resists thermal degradation from nearby heat tunnels.
Lab Oven Manipulator
Handles sample trays inside high-temperature laboratory ovens up to 150 C, relying on the magnetic piston for DMSE electronic sensor feedback without external mechanics.
Is the Airtac SE32 Standard Cylinder SE32X250SH the Right Cylinder?
Delivering 402 N push at 0.5 MPa, this 32 mm bore fits light-duty cycling. If your process requires less force, you lack a smaller standard ISO bore below 32 mm; if you need more power, stepping up to the 40 mm bore yields 628 N push at 0.5 MPa. Because this configuration uses a 250 mm stroke, the 12 mm rod and front bearing face bending stress under lateral loads, so an external guide rail is recommended to prevent premature wear.
As a dimensionally interchangeable ISO 15552 cylinder, it serves as a drop-in replacement for other ISO 15552 profile cylinders using the existing mounting hardware, PT1/8 port, and M10x1.25 rod thread. Note that the adjustable air cushion only decelerates the piston near stroke end; it does not hold the load if air pressure is lost. For position holding, use a BSE rod lock variant.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE32 Standard Cylinder SE32X250SH FAQ
The SE32X250SH generates 402 N push and 345 N pull at 0.5 MPa, 563 N push at 0.7 MPa, and a maximum of 82 kgf at 1.0 MPa. It operates at speeds between 30 and 800 mm/s.
Yes, it is dimensionally interchangeable per ISO 15552 and serves as a drop-in replacement for other profile cylinders using standard mounting hardware. However, it cannot hold a load without air pressure; the adjustable cushion only decelerates the piston near stroke end. For true position holding, consider the BSE rod lock variant.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE32 Standard Cylinder SE32X250SH
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.