Airtac SE32 Standard Cylinder SE32X300SH
The AirTAC Airtac SE32 Standard Cylinder SE32X300SH is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø32mm bore and 300mm stroke, PT1/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
- BoreØ32 mm
- Stroke300 mm
- Port sizePT1/8
- Acting typeDouble acting
- Rod threadM10×1.25
- CushionAdjustable, 27 mm
About the Airtac SE32 Standard Cylinder SE32X300SH
The AirTAC SE32X300SH is a double-acting, single-rod ISO 15552 profile cylinder engineered for compact, high-temperature tasks. It delivers a push force of 402 N at 0.5 MPa (563 N at 0.7 MPa) over a 300 mm stroke, driven by a 12 mm rod and PT1/8 port. The H designation equips it with a Viton (FKM) seal, extending the operating temperature range up to 150 C for harsh industrial environments.
This unit features a square extruded aluminum barrel without external tie rods, yielding a flush, corrosion-resistant profile that simplifies mounting. The built-in S magnet enables position detection with AirTAC CMSE (reed) or DMSE (electronic) sensors, while the field-adjustable pneumatic cushioning at both ends lets you precisely tune end-of-stroke deceleration to dampen mechanical shock.
Airtac SE32 Standard Cylinder SE32X300SH Technical Specifications
| Model | Airtac SE32 Standard Cylinder SE32X300SH |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø32 mm |
| Stroke | 300 mm |
| Acting type | Double acting |
| Port size | PT1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø32mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 402 N | 346 N |
| 0.7 MPa | 563 N | — |
| Max (@1.0 MPa) | 82 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE32 Standard Cylinder SE32X300SH
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 32 | Bore size in mm. |
| ×300 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE32 Standard Cylinder SE32X300SH Is Used
Lab Thermal Ejector
Actuates a high-temperature ejection gate in a lab testing oven, utilizing the 150 C FKM seal and 402 N push force to clear samples safely.
Heat Shrink Wrapper
Cycles a 300 mm stroke diverter arm on a shrink-wrap tunnel, where the Viton seal withstands ambient radiant heat and the S magnet confirms arm position.
Hot Stamping Feed
Pushes lightweight aluminum blanks into a hot stamping press using its 32 mm bore, relying on adjustable cushioning to soften the 300 mm extension stop.
Is the Airtac SE32 Standard Cylinder SE32X300SH the Right Cylinder?
Selecting the SE32X300SH is ideal when you need 402 N of push force at 0.5 MPa in a hot environment. If your application requires less force, the SE40 bore is actually the next step up (628 N push at 0.5 MPa), while there is no smaller standard ISO 15552 bore below 32 mm in the AirTAC range. Because this model uses a 300 mm stroke, the 12 mm piston rod experiences increased bending moments under side loads; always use an external guide rail to prevent rod-bearing wear and seal failure.
As a true ISO 15552 profile cylinder, it serves as a drop-in replacement for other ISO 15552 cylinders, matching standard mounting dimensions and port locations. Remember that the adjustable air cushion only decelerates the piston near stroke end; it does not lock or hold the load. If your process loses air pressure and requires the rod to stay fixed, you must integrate a BSE rod lock or an external pilot-operated check valve.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE32 Standard Cylinder SE32X300SH FAQ
At 0.5 MPa, this 32 mm bore cylinder provides 402 N of push force and 345 N of pull force. At 0.7 MPa, the push force is 563 N, and the maximum push force is 82 kgf at 1.0 MPa. The FKM seal allows operation from 0 to 150 C, with a speed range of 30-800 mm/s.
Yes, its standardized ISO 15552 mounting dimensions make it a drop-in replacement for other ISO 15552 profile cylinders. However, it does not hold its position when air is lost; the adjustable cushion only decelerates the piston near stroke end. For position holding, use a BSE rod lock variant.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE32 Standard Cylinder SE32X300SH
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.