Airtac SE32 Standard Cylinder SE32X350SLB
The AirTAC Airtac SE32 Standard Cylinder SE32X350SLB is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø32mm bore and 350mm stroke, PT1/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
- BoreØ32 mm
- Stroke350 mm
- Port sizePT1/8
- Acting typeDouble acting
- Rod threadM10×1.25
- CushionAdjustable, 27 mm
About the Airtac SE32 Standard Cylinder SE32X350SLB
The AirTAC SE32X350SLB is a double-acting, single-rod ISO 15552 profile cylinder engineered for compact pneumatics. It generates 402 N of push force and 345 N of pull force at 0.5 MPa, utilizing a 32 mm bore and 350 mm stroke. The extruded aluminum barrel omits external tie rods, yielding a smooth, corrosion-resistant body that mounts flush against machine frames.
This specific configuration includes an LB foot mounting bracket for rigid base attachment and a built-in magnet (-S) for position sensing. The integrated magnet interfaces directly with AirTAC CMSE reed switches and DMSE electronic sensors along the three-sided sensor groove. Field-adjustable pneumatic cushioning at both stroke ends allows you to tune deceleration via a set screw, preventing harsh end-stop impacts during high-speed 30-800 mm/s cycles.
Airtac SE32 Standard Cylinder SE32X350SLB Technical Specifications
| Model | Airtac SE32 Standard Cylinder SE32X350SLB |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø32 mm |
| Stroke | 350 mm |
| Acting type | Double acting |
| Port size | PT1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø32mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 402 N | 346 N |
| 0.7 MPa | 563 N | — |
| Max (@1.0 MPa) | 82 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE32 Standard Cylinder SE32X350SLB
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 32 | Bore size in mm. |
| ×350 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE32 Standard Cylinder SE32X350SLB Is Used
Package Diverter Pusher
Ideal for redirecting small cartons on a packaging line, where the 350 mm stroke provides the reach to clear a 300 mm conveyor belt and the 402 N push force easily overcomes box friction.
Lab Sample Dispenser
Moves test tubes or vials into a processing carousel, using the built-in magnet and CMSE sensor to confirm the exact end-of-travel position before the dispensing head actuates.
PCB Panel Ejector
Extracts lightweight printed circuit boards from test fixtures, relying on the smooth tie-rod-less profile to avoid snagging delicate components while the adjustable cushion softens the ejection stop.
Is the Airtac SE32 Standard Cylinder SE32X350SLB the Right Cylinder?
When sizing this actuator, compare its 402 N push at 0.5 MPa against the next bore up: the SE40 provides 628 N of thrust, which is better for heavier tooling. If your load is lighter, dropping down to a bore 32 is the minimum standard ISO 15552 option available. Because this is a 350 mm stroke exceeding the 300 mm threshold, the 12 mm rod and bearing are subject to bending under lateral loads; always support the payload with an external linear guide to prevent premature seal wear. As a standard ISO 15552 profile cylinder, it serves as a drop-in replacement for any cylinder sharing the 32 mm bore footprint, utilizing a PT1/8 port and LB mounting hardware. Note that the air cushion only decelerates the piston near stroke end and does not hold the load if air pressure is lost.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE32 Standard Cylinder SE32X350SLB FAQ
At 0.5 MPa, the SE32X350SLB delivers 402 N of push force and 345 N of pull force. At 0.7 MPa, the push force is 563 N. The maximum push force is 82 kgf when operating at the maximum 1.0 MPa pressure.
Yes. The SE32X350SLB is built to the ISO 15552 dimensional standard, meaning it shares the exact mounting footprint, PT1/8 port size, and 32 mm bore spacing as other ISO 15552 cylinders. It functions as a direct drop-in replacement without needing to modify the machine frame.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE32 Standard Cylinder SE32X350SLB
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.