Airtac SE32 Standard Cylinder SE32X350SN
The AirTAC Airtac SE32 Standard Cylinder SE32X350SN is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø32mm bore and 350mm stroke, PT1/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
- BoreØ32 mm
- Stroke350 mm
- Port sizePT1/8
- Acting typeDouble acting
- Rod threadM10×1.25
- CushionAdjustable, 27 mm
About the Airtac SE32 Standard Cylinder SE32X350SN
The AirTAC SE32X350SN is a double-acting, single-rod ISO 15552 profile cylinder with a 32mm bore and 350mm stroke. It delivers a push force of 402 N at 0.5 MPa and is built with an NBR seal for reliable performance in standard temperature ranges. The square extruded aluminum barrel omits external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machine frames.
This unit includes a built-in magnet (-S) for direct compatibility with AirTAC CMSE reed and DMSE electronic sensors, enabling precise end-of-stroke detection. Field-adjustable pneumatic cushioning at both ends allows you to fine-tune the deceleration of the 12mm hard-chrome rod, softening hard end stops during high-speed cycling.
Airtac SE32 Standard Cylinder SE32X350SN Technical Specifications
| Model | Airtac SE32 Standard Cylinder SE32X350SN |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø32 mm |
| Stroke | 350 mm |
| Acting type | Double acting |
| Port size | PT1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø32mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 402 N | 346 N |
| 0.7 MPa | 563 N | — |
| Max (@1.0 MPa) | 82 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE32 Standard Cylinder SE32X350SN
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 32 | Bore size in mm. |
| ×350 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE32 Standard Cylinder SE32X350SN Is Used
PCB Depaneling Router
Provides the 402 N push needed to drive the cutting head of a PCB depaneling router across 350mm, ensuring clean, vibration-free board separation.
Lab Dispenser Positioning
Moves reagent dispenser heads across a 350mm width with precise extend and retract cycles, utilizing CMSE sensors to confirm nozzle position.
Small Parts Ejection
Ejects molded plastic components from a 32mm bore fixture, using adjustable end cushions to absorb the kinetic energy of the 350mm stroke.
Is the Airtac SE32 Standard Cylinder SE32X350SN the Right Cylinder?
If the 402 N push at 0.5 MPa is too high for your application, stepping down is not an option as 32mm is the smallest standard bore; you would need to reduce your operating pressure. If you require more force, stepping up to the 40mm bore provides a 628 N push at 0.5 MPa. Because this is a standard double-acting cylinder, it will drift if air is lost or the valve is centered; use a BSE rod lock for position holding. At 350mm stroke, the unsupported 12mm rod is susceptible to bending under side loads—always use an external guide to prevent rod-bearing damage.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE32 Standard Cylinder SE32X350SN FAQ
At 0.5 MPa, the push force is 402 N and the pull force is 345 N. At 0.7 MPa, the push force is 563 N. The maximum push force is 82 kgf at 1.0 MPa.
Yes, the SE32X350SN is dimensionally interchangeable per ISO 15552 standards, allowing it to drop-in replace other ISO 15552 cylinders using existing mounting hardware and PT1/8 ports.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE32 Standard Cylinder SE32X350SN
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.