Airtac SE32 Standard Cylinder SE32X462S
The AirTAC Airtac SE32 Standard Cylinder SE32X462S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø32mm bore and 462mm stroke, PT1/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
- BoreØ32 mm
- Stroke462 mm
- Port sizePT1/8
- Acting typeDouble acting
- Rod threadM10×1.25
- CushionAdjustable, 27 mm
About the Airtac SE32 Standard Cylinder SE32X462S
The AirTAC SE32X462S is a double-acting single-rod ISO 15552 profile cylinder engineered for compact pneumatics. It delivers a push force of 402 N and a pull force of 345 N at 0.5 MPa, making it suitable for lighter-duty actuation. The extruded aluminum square barrel omits external tie rods, yielding a flush, corrosion-resistant body that mounts cleanly in tight machine envelopes.
This specific unit includes a built-in magnet (-S) for non-contact position detection using AirTAC CMSE reed or DMSE electronic sensors, which seat directly into the sensor grooves on three sides of the body. Field-adjustable pneumatic cushioning at both ends allows technicians to tune end-of-stroke deceleration via a set screw, actively slowing the piston rather than relying on a fixed rubber bumper.
Airtac SE32 Standard Cylinder SE32X462S Technical Specifications
| Model | Airtac SE32 Standard Cylinder SE32X462S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø32 mm |
| Stroke | 462 mm |
| Acting type | Double acting |
| Port size | PT1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø32mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 402 N | 346 N |
| 0.7 MPa | 563 N | — |
| Max (@1.0 MPa) | 82 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE32 Standard Cylinder SE32X462S
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 32 | Bore size in mm. |
| ×462 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE32 Standard Cylinder SE32X462S Is Used
PCB Depaneling Router
Provides the 402 N push force and 462 mm travel needed to drive a depaneling router bit across large 460 mm circuit board panels.
Pouch Pick-and-Place
Uses the built-in magnet with DMSE sensors to confirm retraction at high speed, moving packaged pouches across a 460 mm wide conveyor lane.
Lab Dispenser Positioning
Shifts a volumetric liquid dispenser head across a 462 mm testing array, relying on adjustable end cushions to prevent fluid splashing on hard stops.
Is the Airtac SE32 Standard Cylinder SE32X462S the Right Cylinder?
With a 32 mm bore generating 402 N push at 0.5 MPa, this cylinder fits applications needing precise, low-force movement. If your load demands less force, there is no smaller standard ISO 15552 bore in the AirTAC range. If you need substantially more thrust, stepping up to the 40 mm bore yields 628 N push at 0.5 MPa. Because the 462 mm stroke is non-standard and exceeds typical catalog lengths, verify lead times for made-to-order production. At 462 mm, the unsupported rod length increases bending stress on the M10x1.25 thread and front bearing; an external guide rail is strongly recommended to prevent side-load wear. Note that a standard SE cylinder will drift if air pressure is lost—use a BSE rod lock variant if the load must be held safely without live pressure. As a true ISO 15552 profile cylinder, it offers drop-in dimensional interchangeability with other ISO 15552 cylinders, sharing standard mounting hardware like FA flanges and LB foot brackets.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE32 Standard Cylinder SE32X462S FAQ
The SE32X462S generates 402 N push and 345 N pull at 0.5 MPa, 563 N push at 0.7 MPa, and a maximum push of 82 kgf at 1.0 MPa. It features a 32 mm bore, 12 mm rod, M10x1.25 rod thread, PT1/8 port, and operates at 30-800 mm/s.
No, the standard SE series is double-acting and cannot hold a load if air is lost or exhausted; the piston will drift. The adjustable air cushion only decelerates the piston near the stroke ends and does not act as a mechanical lock. For fail-safe load holding, consider the AirTAC BSE rod lock variant.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE32 Standard Cylinder SE32X462S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.