Airtac SE32 Standard Cylinder SE32X560S
The AirTAC Airtac SE32 Standard Cylinder SE32X560S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø32mm bore and 560mm stroke, PT1/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
- BoreØ32 mm
- Stroke560 mm
- Port sizePT1/8
- Acting typeDouble acting
- Rod threadM10×1.25
- CushionAdjustable, 27 mm
About the Airtac SE32 Standard Cylinder SE32X560S
The AirTAC SE32X560S is a double-acting, single-rod ISO 15552 profile cylinder with a 32 mm bore and 560 mm stroke. It delivers 402 N of push force and 345 N of pull force at 0.5 MPa, making it well-suited for lighter-duty linear actuation. The extruded aluminum barrel lacks external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machine frames.
This specific unit includes a built-in magnet (-S) for position sensing with AirTAC CMSE reed or DMSE electronic switches. To protect end caps and piston rods from kinetic impact, it features field-adjustable pneumatic cushioning at both ends, allowing technicians to fine-tune deceleration as cycle speeds vary.
Airtac SE32 Standard Cylinder SE32X560S Technical Specifications
| Model | Airtac SE32 Standard Cylinder SE32X560S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø32 mm |
| Stroke | 560 mm |
| Acting type | Double acting |
| Port size | PT1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø32mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 402 N | 346 N |
| 0.7 MPa | 563 N | — |
| Max (@1.0 MPa) | 82 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE32 Standard Cylinder SE32X560S
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 32 | Bore size in mm. |
| ×560 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE32 Standard Cylinder SE32X560S Is Used
Package Diverting
Sorts light cardboard cartons on packaging lines where 402 N of push force at 0.5 MPa easily redirects items at high throughput.
Lab Sample Dispensing
Actuates a 560 mm travel gantry to move test tube racks between analysis stations, using the magnet for DMSE electronic position feedback.
Thin Film Alignment
Pushes light gauge metal or plastic sheets into a press bed, utilizing the tie-rod-free profile barrel for tight lateral mounting clearances.
Is the Airtac SE32 Standard Cylinder SE32X560S the Right Cylinder?
At 0.5 MPa, this 32 mm bore cylinder provides 402 N push and 345 N pull force. If your application requires less force, there is no smaller standard ISO 15552 bore available in the AirTAC range. If you need substantially more power, stepping up to the 40 mm bore increases push force to 628 N at 0.5 MPa. Because the 560 mm stroke exceeds 300 mm, side loads create significant bending moments on the 12 mm rod and front bearing; always support the load with an external guide rail to prevent premature seal wear.
For drop-in retrofits, match the 32 mm bore, 560 mm stroke, PT1/8 port, and required mounting accessory. The -S magnet enables CMSE/DMSE sensors for end-of-stroke confirmation. Remember that the adjustable air cushion only decelerates the piston near stroke end; it does not lock or hold the load if air pressure drops.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE32 Standard Cylinder SE32X560S FAQ
At 0.5 MPa, the 32 mm bore delivers 402 N push and 345 N pull force. At 0.7 MPa, push increases to 563 N, with a maximum push of 82 kgf at 1.0 MPa. Operating speed ranges from 30-800 mm/s.
Yes, the SE32X560S is dimensionally interchangeable per ISO 15552 standards, sharing identical mounting interface dimensions with other profile cylinders. You can swap it directly using existing FA, LB, or TC mounting hardware and PT1/8 ports.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE32 Standard Cylinder SE32X560S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.