Airtac SE32 Standard Cylinder SE32X600SLB
The AirTAC Airtac SE32 Standard Cylinder SE32X600SLB is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø32mm bore and 600mm stroke, PT1/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
- BoreØ32 mm
- Stroke600 mm
- Port sizePT1/8
- Acting typeDouble acting
- Rod threadM10×1.25
- CushionAdjustable, 27 mm
About the Airtac SE32 Standard Cylinder SE32X600SLB
The AirTAC SE32X600SLB is a double-acting, single-rod ISO 15552 profile cylinder engineered for a 32 mm bore and 600 mm stroke. It generates 402 N of push force at 0.5 MPa and relies on a hard-chrome plated Ø12 mm piston rod with an M10x1.25 thread. Because the square extruded aluminum barrel omits external tie rods, the body is highly resistant to corrosion and allows for flush mounting against machine frames, saving valuable space in tight assemblies.
This specific configuration includes the LB foot mounting bracket for secure horizontal installation and a built-in magnet (-S) for position sensing. The integrated magnet is fully compatible with AirTAC CMSE reed and DMSE electronic sensors, which drop directly into the sensor grooves on three sides of the body. Furthermore, the end caps house field-adjustable pneumatic cushioning, letting technicians dial in the exact deceleration needed to prevent hard end-stop impacts during high-speed cycling.
Airtac SE32 Standard Cylinder SE32X600SLB Technical Specifications
| Model | Airtac SE32 Standard Cylinder SE32X600SLB |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø32 mm |
| Stroke | 600 mm |
| Acting type | Double acting |
| Port size | PT1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø32mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 402 N | 346 N |
| 0.7 MPa | 563 N | — |
| Max (@1.0 MPa) | 82 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE32 Standard Cylinder SE32X600SLB
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 32 | Bore size in mm. |
| ×600 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE32 Standard Cylinder SE32X600SLB Is Used
Package Diverter Gates
Actuates lightweight routing flaps on logistics conveyor lines, where the 402 N push force is sufficient to pivot aluminum gates and the 600 mm stroke provides the full reach needed to clear wide sorting belts.
PCB Shuttle Ejection
Pushes printed circuit board trays out of pick-and-place machines, utilizing the built-in -S magnet to trigger DMSE electronic sensors for precise end-of-stroke position confirmation.
Film Roll Web Tracking
Guides packaging film tensioning arms on vertical form-fill-seal equipment, where the LB foot mount stabilizes the cylinder body during rapid 30-800 mm/s extension and retraction cycles.
Is the Airtac SE32 Standard Cylinder SE32X600SLB the Right Cylinder?
When sizing this 32 mm bore model, evaluate your force margins carefully: it provides 402 N of push at 0.5 MPa, so if your load requires less energy, stepping down is not an option as this is the smallest standard SE bore. If you need substantially more thrust, the next size up is the 40 mm bore, which delivers 628 N of push at 0.5 MPa. For this 600 mm stroke, the unsupported piston rod is highly susceptible to bending under side loads; always incorporate an external guide rail to prevent premature rod-bearing wear. Also, note that a standard SE cylinder will drift and cannot hold a load if air pressure is lost or the valve is centered—use a BSE rod lock variant if static holding is required.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE32 Standard Cylinder SE32X600SLB FAQ
The 32 mm bore SE32X600SLB generates 402 N of push force and 345 N of pull force at 0.5 MPa. At 0.7 MPa, the push force increases to 563 N, and the maximum push force is 82 kgf at 1.0 MPa. It operates at speeds of 30-800 mm/s, uses a PT1/8 port, and has a 27 mm cushion length at both ends.
Yes, the SE32X600SLB is dimensionally interchangeable per ISO 15552 standards, meaning it shares the exact same mounting footprint and LB accessory interface as competing ISO 15552 profile cylinders. The pneumatic cushioning at both ends is field-adjustable via a set screw, allowing you to tune the deceleration of the piston near stroke end to soften hard impacts, though it does not lock or hold the load.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE32 Standard Cylinder SE32X600SLB
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.