Airtac SE32 Standard Cylinder SE32X750
The AirTAC Airtac SE32 Standard Cylinder SE32X750 is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø32mm bore and 750mm stroke, PT1/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
- BoreØ32 mm
- Stroke750 mm
- Port sizePT1/8
- Acting typeDouble acting
- Rod threadM10×1.25
- CushionAdjustable, 27 mm
About the Airtac SE32 Standard Cylinder SE32X750
The AirTAC SE32X750 is a double-acting single-rod ISO 15552 profile cylinder, delivering 402 N of push force at 0.5 MPa and 563 N at 0.7 MPa. Its extruded aluminum barrel lacks external tie rods, yielding a compact, corrosion-resistant body that mounts flush against frames while leaving three sensor grooves open for switches. This 32 mm bore unit uses a PT1/8 port and a 12 mm hard-chrome rod.
Because this 750 mm stroke exceeds the 600 mm threshold for a 32 mm bore, it is built to order as a non-standard stroke configuration. The end caps feature field-adjustable pneumatic cushioning at both ends, allowing technicians to tune the 27 mm cushion length via a set screw to soften hard end stops at speed. Note this SKU lacks a built-in magnet, so it will not trigger CMSE or DMSE position sensors without modification.
Airtac SE32 Standard Cylinder SE32X750 Technical Specifications
| Model | Airtac SE32 Standard Cylinder SE32X750 |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø32 mm |
| Stroke | 750 mm |
| Acting type | Double acting |
| Port size | PT1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø32mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 402 N | 346 N |
| 0.7 MPa | 563 N | — |
| Max (@1.0 MPa) | 82 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE32 Standard Cylinder SE32X750
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 32 | Bore size in mm. |
| ×750 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE32 Standard Cylinder SE32X750 Is Used
Package Diverter Gate
Actuates a lightweight routing flap on a packaging conveyor, using the 750 mm stroke to shift cardboard cartons between sorting lanes.
PCB Panel Ejector
Pushes fabricated printed circuit boards out of a test fixture with 402 N of force, relying on the compact tie-rod-free profile to fit tight machine cells.
Lab Sample Transport
Moves light sample trays across a 750 mm gap in analytical equipment, utilizing the 30-800 mm/s speed range and adjustable end cushions to prevent spillage.
Is the Airtac SE32 Standard Cylinder SE32X750 the Right Cylinder?
When sizing this 32 mm bore model, which pushes 402 N at 0.5 MPa, you can step down to a 25 mm bore for lighter loads or step up to a 40 mm bore for 628 N of push force. This SE32X750 uses a PT1/8 port, a 12 mm rod with an M10x1.25 thread, and basic mounting. Remember that a standard double-acting cylinder drifts when air is lost or a valve is centered; the adjustable air cushion only decelerates the piston near stroke end and does not lock the load.
At 750 mm of stroke, the unsupported 12 mm rod is highly susceptible to bending under side loads. To prevent premature rod-bearing wear and piston scoring, always pair this unit with an external linear guide to carry the actual workload.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE32 Standard Cylinder SE32X750 FAQ
The SE32X750 provides 402 N of push force and 345 N of pull force at 0.5 MPa. At 0.7 MPa, the push force is 563 N, with a maximum push capacity of 82 kgf at 1.0 MPa. It has a 32 mm bore, a 750 mm stroke, and operates at speeds of 30-800 mm/s.
Yes. The SE32X750 is a true ISO 15552 / VDMA 24562 profile cylinder, making it dimensionally interchangeable with other ISO 15552 cylinders. It uses the standard mounting interface and an extruded aluminum barrel without external tie rods, allowing drop-in replacement using your existing mounting hardware.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE32 Standard Cylinder SE32X750
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.