Airtac SE32 Standard Cylinder SE32X780S
The AirTAC Airtac SE32 Standard Cylinder SE32X780S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø32mm bore and 780mm stroke, PT1/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
- BoreØ32 mm
- Stroke780 mm
- Port sizePT1/8
- Acting typeDouble acting
- Rod threadM10×1.25
- CushionAdjustable, 27 mm
About the Airtac SE32 Standard Cylinder SE32X780S
The AirTAC SE32X780S is a double-acting single-rod profile cylinder built to the ISO 15552 dimension standard, delivering a 402 N push force at 0.5 MPa. Its square extruded aluminum barrel eliminates external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machine frames while retaining the standardized ISO 15552 mounting interface for seamless retrofits.
This 32 mm bore unit travels an extended 780 mm stroke and includes a built-in magnet (-S) for non-contact position sensing with AirTAC CMSE reed or DMSE electronic switches. Field-adjustable air cushioning at both ends allows technicians to tune end-of-stroke deceleration via a setscrew, softening hard mechanical stops during high-speed 30-800 mm/s cycling.
Airtac SE32 Standard Cylinder SE32X780S Technical Specifications
| Model | Airtac SE32 Standard Cylinder SE32X780S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø32 mm |
| Stroke | 780 mm |
| Acting type | Double acting |
| Port size | PT1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø32mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 402 N | 346 N |
| 0.7 MPa | 563 N | — |
| Max (@1.0 MPa) | 82 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE32 Standard Cylinder SE32X780S
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 32 | Bore size in mm. |
| ×780 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE32 Standard Cylinder SE32X780S Is Used
Package Sorting Diverter
Uses the 780 mm stroke and 402 N push force to extend diverter arms across a 700 mm wide conveyor belt, routing mixed parcels into specific warehouse lanes at high speed.
PCB Edge-Trimming Shuttle
Moves lightweight routing spindles along the 780 mm axis to trim printed circuit board edges, leveraging the compact tie-rod-free profile to minimize frame interference.
Lab Sample Dispenser
Actuates a sliding rack to present vials to an analytical probe, relying on the -S magnet and DMSE electronic sensors to confirm full extension without physical contact.
Is the Airtac SE32 Standard Cylinder SE32X780S the Right Cylinder?
Choosing the SE32X780S means sizing for a 402 N push at 0.5 MPa. If your payload requires less force, stepping down to the 32 mm bore's closest neighbor is not an option as it is the smallest available, but stepping up to the 40 mm bore yields a higher 628 N push for heavier loads. Remember that a plain SE cylinder relies entirely on live air pressure to hold position; if air is lost or the valve centers, the piston will drift, so consider a BSE rod lock variant for fail-safe holding.
Because this 780 mm stroke creates a long lever arm on the 12 mm rod, side loads can induce severe bending moments on the rod bearing. For any application exceeding 300 mm of travel, adding an external linear guide is strongly recommended to prevent premature seal wear and piston scoring.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE32 Standard Cylinder SE32X780S FAQ
At 0.5 MPa, the push force is 402 N and the pull force is 345 N. At 0.7 MPa, the push force increases to 563 N. The maximum push force is 82 kgf at 1.0 MPa, and the operational speed range is 30-800 mm/s.
Yes, the SE32X780S is dimensionally interchangeable per ISO 15552 mounting dimensions, allowing it to drop-in replace other standard profile cylinders. It uses a PT1/8 port and features field-adjustable air cushions at both ends to fine-tune stopping.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE32 Standard Cylinder SE32X780S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.