
The AirTAC SE40 Standard Cylinder SE40X30SFA is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø40mm bore and 30mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE40X30SFA is a double-acting single-rod profile cylinder delivering 628 N of push force at 0.5 MPa and 879 N at 0.7 MPa. Built to the ISO 15552 standard, its square extruded aluminum barrel eliminates external tie rods, yielding a compact footprint that mounts flush against machine frames while resisting corrosion.
This specific configuration includes a front flange (FA) for secure face-mounting and a built-in magnet (S) for position sensing. The integrated magnetic piston interfaces directly with AirTAC CMSE reed or DMSE electronic switches fitted into the body grooves, while field-adjustable air cushions at both ends absorb end-of-stroke impact.
| Model | Airtac SE40 Standard Cylinder SE40X30SFA |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø40 mm |
| Stroke | 30 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M12×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 628 N | 528 N |
| 0.7 MPa | 880 N | — |
| Max (@1.0 MPa) | 128 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 40 | Bore size in mm. |
| ×30 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Provides 628 N of precise clamping force on printed circuit board routing fixtures, utilizing the 30 mm stroke to secure panels rapidly before cutting.
Actuates a short-stroke routing gate on a packaging conveyor, where the FA front flange holds firm against lateral impact from passing cartons.
Drives a compact folding arm on a case erector, using the integrated magnet and DMSE sensor to confirm flap position before tape application.
Selecting this 40 mm bore with a 30 mm stroke suits short-travel clamping and lifting tasks requiring 628 N push at 0.5 MPa. If your application demands less force, stepping down to the 32 mm bore yields 402 N push; conversely, moving up to the 50 mm bore provides 982 N push for heavier payloads. Because the stroke is under 300 mm, side-load stress on the rod bearing is minimal compared to longer units.
This model is dimensionally interchangeable with other ISO 15552 cylinders, allowing a direct retrofit using existing hardware. It features a PT1/4 port, an FA front flange, and a magnetic piston for CMSE/DMSE sensors. Note that the adjustable cushion decelerates the piston near stroke end but does not lock the load; if air pressure drops, the rod will drift.
AirtacDistr lists every SE40 order code with its price on one page at https://airtacdistr.com/products/airtac-se40-iso-air-cylinder
Quick checklist
At 0.5 MPa, the push force is 628 N and the pull force is 528 N. At 0.7 MPa, the push force increases to 879 N. The maximum push force is 128 kgf at 1.0 MPa, and the operational speed range is 30-800 mm/s.
Yes, the SE40X30SFA is dimensionally interchangeable per ISO 15552 standards. You can drop it into existing mounts using the FA front flange, matching the 40 mm bore and 30 mm stroke footprint without altering the machine base.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.