
The AirTAC SEJ Adjustable Cylinder SEJ50X350-20 is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 20mm window, so this Ø50mm unit covers an effective stroke of 330–350mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ50X350-20 is a double-acting, double-rod ISO 15552 profile cylinder featuring a 20mm adjustable stroke window, allowing you to dial the retract end from 330 to 350mm. A rod exits both ends, ensuring the annulus area remains identical in both directions. This yields an equal force of 825 N each way at 0.5 MPa, preventing speed discrepancies between extend and retract motions.
Because the rear rod extends through the back cap, it provides a convenient mounting point for a cam or flag, though the overall length is longer than a single-rod unit. The retract position is set via a mechanical stop screw on the back rod; you dial it in, then lock it to secure the exact end-position on the machine without swapping hardware. This SKU has no magnet, so it will not host CMSE or DMSE sensors out of the box.
| Model | Airtac SEJ Adjustable Cylinder SEJ50X350-20 |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø50 mm |
| Nominal stroke | 350 mm |
| Adjustment window | 20 mm (330–350 mm) |
| Configuration | Double rod, double acting |
| Port size | PT1/4 |
| Rod thread | M16×1.5 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 20mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 825 N |
| 0.7 MPa | 1155 N |
| Max (@1.0 MPa) | 168 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 50 | Bore size in mm. |
| ×350 | Nominal stroke length in mm. |
| -20 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Dial in the 330-350mm retract stop to perfectly seat sheet metal blanks against a back gauge, utilizing the 825 N both-way force without re-mounting hardware.
Adjust the retract position on the fly to accommodate different carton heights, using the equal double-rod force to push and pull the folding mechanism reliably.
Set the exact stop location for varying pallet depths on a conveyor line, locking the back-rod screw to handle the 1154 N impact of incoming loads at 0.7 MPa.
Confirm this 20mm adjustment window covers your commissioning range; if you need a wider fine-tuning band, consider a 50mm window variant. For sizing both ways: stepping down to a 40mm bore drops the both-way force to 528 N at 0.5 MPa, while stepping up to a 63mm bore increases it to 1402 N. If your end-position never changes after commissioning, a fixed-stroke SED offers the same ISO 15552 mounting in a shorter package. To replace this cylinder, match the 50mm bore, 350mm stroke, PT1/4 port, and your specific mounting from the SEJ set (Basic, FA, LB, TC, FTC, TCM1, TCM2—note FB, CA, CB, and CR are omitted). At 350mm stroke, account for side loads and guide external rods to prevent binding. Remember, the adjustable air cushion decelerates near stroke end but is not a lock; a plain SEJ does not hold position on air loss, so use a BSED or external rod lock for fail-safe holding.
AirtacDistr lists every SEJ50 order code with its price on one page at https://airtacdistr.com/products/airtac-sej50-adjustable-cylinder
Quick checklist
A stop screw on the rear protruding rod lets you mechanically shorten the retract stroke by up to 20mm. The effective stroke range is 330-350mm; you dial in the exact end-position and lock the screw, meaning one cylinder covers a range without changing hardware.
Because the rod exits both ends, the force is identical in both directions: 825 N at 0.5 MPa, 1154 N at 0.7 MPa, and a maximum of 168 kgf at 1.0 MPa.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.