verified AirTAC China Authorized Export Seller shield 100% Genuine AirTAC Parts workspace_premium 1-Year Warranty
appsShop by Modelexpand_more
person shopping_cart Request a QuoteQuote
AirTAC SEJ Series · ISO 15552 Adjustable-Stroke Cylinder

Airtac SEJ Adjustable Cylinder SEJ50X350-50S

The AirTAC SEJ Adjustable Cylinder SEJ50X350-50S is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 50mm window, so this Ø50mm unit covers an effective stroke of 300–350mm without changing cylinders. Force is equal in both directions.

  • BoreØ50 mm
  • Nominal stroke350 mm
  • Adjust window50 mm
  • Effective stroke300–350 mm
  • Port sizePT1/4
  • CushionAdjustable, 30 mm
$138.61 $146.11Save 5% Standard model — usually dispatched in 3-5 days
Request a Quote
  • No minimum order. A single piece can be ordered.
  • Shipped from our own warehouse: most standard models dispatch in 3–5 days; custom and non-standard models take 8–10 business days. Transit time after that depends on the destination.
Compare every SEJ50 stroke, mounting and version on one page All SEJ50 codes →
verified Genuine AirTAC workspace_premium 1-year warranty bolt Reply in 7 h

About the Airtac SEJ Adjustable Cylinder SEJ50X350-50S

The AirTAC SEJ50X350-50S is a double-acting, double-rod ISO 15552 profile cylinder with a 50 mm bore and 350 mm nominal stroke. A rod exits both ends, yielding identical annulus areas so output force is equal in both directions at 825 N each way at 0.5 MPa. An integrated magnet supports CMSE reed and DMSE electronic sensors for position detection.

The rear rod features a mechanical stop screw providing a 50 mm adjustment window, allowing you to dial the retract stroke down to 300 mm for precise machine commissioning. Built to ISO 15552 dimensional standards with adjustable air cushions at both ends, it uses a PT1/4 port and a 20 mm rod with an M16x1.5 thread.

Airtac SEJ Adjustable Cylinder SEJ50X350-50S Technical Specifications

ModelAirtac SEJ Adjustable Cylinder SEJ50X350-50S
SeriesSEJ ISO 15552 adjustable-stroke cylinder
Bore sizeØ50 mm
Nominal stroke350 mm
Adjustment window50 mm (300–350 mm)
ConfigurationDouble rod, double acting
Port sizePT1/4
Rod threadM16×1.5
Operating pressure0.15 – 1.0 MPa
Proof pressure1.5 MPa
Temperature-20 to +70 °C (0–150 °C with FKM seals)
Speed range30 – 800 mm/s
CushionAdjustable, 30 mm

Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 50mm window. Port options: PT (standard) / G (BSPP).

Theoretical Output Force (Ø50mm)

PressureForce (both directions)
0.5 MPa825 N
0.7 MPa1155 N
Max (@1.0 MPa)168 kgf

A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.

Model Code: Airtac SEJ Adjustable Cylinder SEJ50X350-50S

SEJISO 15552 double-rod double-acting cylinder with adjustable stroke.
50Bore size in mm.
×350Nominal stroke length in mm.
-50Adjustment stroke window in mm (options: 10/20/30/40/50/75/100).
-SOptional built-in magnet for CMSE / DMSE sensor sensing.

Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).

Where the Airtac SEJ Adjustable Cylinder SEJ50X350-50S Is Used

precision_manufacturing

Press Tonnage Calibration

Dial the 50 mm retract window to precisely set the working stroke on a small pneumatic press, utilizing the 825 N both-way force for consistent material deformation.

conveyor_belt

Variable Stop Diverter

Adjust the end position to handle changing package sizes on a conveyor line, using the equal push and pull forces to reliably index products without rebalancing pressure.

swap_horiz

Multi-Height Changeover

Fine-tune the retract stroke during machine changeover to accommodate different part heights, locking the back-rod stop screw at the exact required position between 300 and 350 mm.

Is the Airtac SEJ Adjustable Cylinder SEJ50X350-50S the Right Cylinder?

Verify the 50 mm adjustment window covers your required end-position range, letting you fine-tune the retract stroke from 300 to 350 mm on the machine without changing hardware. If you need less force, the 40 mm bore delivers 528 N both ways at 0.5 MPa; if your application demands more push or pull, step up to the 63 mm bore which provides 1402 N each way at 0.5 MPa. If exact positioning is unnecessary, a fixed-stroke SED cylinder is sufficient. Remember that the adjustable air cushion and stop screw only set the mechanical end and decelerate near stroke end; they do not hold position on air loss, so consider an external rod lock for fail-safe holding. At 350 mm stroke, guide external loads to prevent side-load wear on the rod seals. To match an ISO 15552 replacement, confirm the 50 mm bore, 350 mm stroke, 50 mm window, PT1/4 port, and required mounting (Basic, FA, LB, TC, FTC, TCM1, or TCM2).

AirtacDistr lists every SEJ50 order code with its price on one page at https://airtacdistr.com/products/airtac-sej50-adjustable-cylinder

Quick checklist

  • ✓ Need on-machine stroke fine-tuning?
  • ✓ Adjustment window (50mm) covers your range
  • ✓ Equal force both directions OK
  • ✓ Port/thread type (PT/G)
  • ✓ Magnet (-S) for CMSE/DMSE sensors?
Ask an Engineer

Installation & Maintenance Notes

  • check Use clean air filtered to 40µm or finer.
  • check Keep within 0.15 – 1.0 MPa operating pressure.
  • check Set the stop screw within the 50mm window; lock it after adjusting.
  • check Adjust end cushion screws for smooth stops.
  • check Use correct mounting accessory (LB/FA/TC/FTC/TCM1/TCM2).
  • check Installation by qualified personnel per AirTAC docs.

Airtac SEJ Adjustable Cylinder SEJ50X350-50S FAQ

The retract stroke can be dialed back by up to 50 mm using the back-rod stop screw, giving an effective stroke range of 300 to 350 mm. You set the exact end position during commissioning and lock it in place.

Because the rod exits both ends, the force is identical in both directions. It generates 825 N at 0.5 MPa, 1154 N at 0.7 MPa, and a maximum of 168 kgf at 1.0 MPa.

verified

Authorized Export Seller

Genuine AirTAC parts produced by AirTAC factory.

workspace_premium

1-Year Warranty

Covers non-human-caused product damage.

local_shipping

Fast Dispatch

Most standard models are dispatched in 3-5 days.

bolt

Fast Reply

Most inquiries answered within 7 hours.

Related AirTAC SEJ Cylinders

Request a Quote for Airtac SEJ Adjustable Cylinder SEJ50X350-50S

Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.

Thank you. We received your request for SEJ50X350-50S and will confirm price, availability and lead time — usually within 7 hours.

For the fastest response, keep the complete model number above and include a clear photo of the product label. If photo upload is unavailable, email photos to [email protected] with your model number.