Airtac TN Double Axis Double Rod Cylinder TN16X75S
The AirTAC Airtac TN Double Axis Double Rod Cylinder TN16X75S is a genuine TN twin-rod (double-rod) double-acting cylinder, 16 mm bore. Two parallel rods on one plate resist bending and twisting and let the load mount without rotating. It delivers about 201.1 N of push at 0.5 MPa. A front bumper cushions the impact and adjusts the stroke over a -5 to 0 mm range.
- TypeTwin-rod, double acting
- Standardenterprise standard
- Bore16 mm
- Push thrust @0.5 MPa201.1 N
- Operating pressure0.15 - 1.0 MPa (22 - 145 psi)
- Port sizeM5x0.8
- CushionAdjustable bumper (-5 to 0 mm)
- MagnetStandard (sensor-ready)
- ThreadPT
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac TN Double Axis Double Rod Cylinder TN16X75S
The TN16X75S is a 75 mm-stroke, 16 mm-bore twin-rod cylinder. Two rods run in parallel on a single shared plate, so the load mounts directly without rotating and the assembly resists bending and twisting where a single-rod cylinder of the same footprint would deflect. At 0.5 MPa, the push side of the 16 mm bore produces a theoretical 201.1 N of thrust. An external bumper pad cushions the end of stroke and can also adjust the effective stroke by -5 to 0 mm.
You are ordering a genuine AirTAC part from the TN series, which follows the ENTERPRISE standard across 10/16/20/25/32 mm bores and uses PT ports. A magnet is fitted as standard on the whole series, with slots around the body for magnetic switches. Because overall dimensions and side-load ratings depend on stroke, we confirm them from the datasheet on request.
Airtac TN Double Axis Double Rod Cylinder TN16X75S Technical Specifications
| Model | Airtac TN Double Axis Double Rod Cylinder TN16X75S |
|---|---|
| Type | Twin-rod cylinder, double acting |
| Series / standard | TN (enterprise standard) |
| Bore | 16 mm |
| Push thrust @0.5 MPa | 201.1 N |
| Port size | M5x0.8 (PT thread) |
| Fluid | Air, filtered to 40 um |
|---|---|
| Operating pressure | 0.15 - 1.0 MPa (22 - 145 psi) |
| Proof pressure | 1.5 MPa (215 psi) |
| Temperature | -20 to 70 C |
| Speed range | 30 - 500 mm/s |
| Cushion | Bumper, stroke adjustable -5 to 0 mm |
| Magnet | Standard (magnetic-switch slots around the body) |
Specifications follow the official AirTAC TN/TR twin-rod data. Operating pressure is set by bore (0.2 MPa minimum on the 6 and 10 mm bores). The front cover and piston are short, so avoid an over-long stroke. Overall dimensions vary per stroke and allowable side-load is published as curves — ask us and we confirm from the datasheet.
How to choose
Pick the 16 mm bore when roughly 201.1 N of push thrust at 0.5 MPa covers your job; heavier loads belong on the 20/25/32 mm bores, lighter ones on 10 mm. TN is the ENTERPRISE-standard series with PT ports only - if your circuit needs G or NPT threads, or you want the JIS-standard TR's more precise guidance (higher non-rotating accuracy, lower rod-end deflection and a lengthening sliding-support guide needing no added lubricant), switch to the TR series. 75 mm is within the 16 mm bore's stroke table, but this is a compact short-body cylinder, so avoid stretching past the listed stroke options and check cover clearance. Side-load capability and exact dimensions for your stroke come from the datasheet - ask us and we will provide it.
Applications
Transfer slide
Carries small parts between stations on a plate that cannot rotate, keeping orientation correct at each pick and drop point.
Press-fit assist
Applies even twin-rod thrust to seat light components in assembly fixtures, with the bumper trimming final approach by up to 5 mm.
Stopper gate
Rises and lowers a flow-control stopper on a conveyor line; twin rods stop the blade from cocking sideways under product load.
FAQ
What thread and port options does the TN16X75S offer?
The TN series is a PT-port-only range. This 16 mm bore takes an M5x0.8 port. If your plumbing needs G or NPT threads, that is a reason to move to the TR (JIS-standard) twin-rod series instead.
Can this cylinder take a side load on the plate?
The twin-rod design resists bending and twisting, and the plate mounts the load without rotating, but allowable side load and rod-end deflection are published only as curves, not single numbers. Send us your application and we will confirm the values from the datasheet.