Airtac GAC F.R.L. Unit GAC30010LW
The AirTAC Airtac GAC F.R.L. Unit GAC30010LW is a genuine three-unit F.R.L. combination — a filter, a pressure regulator and a lubricator pre-assembled on one bracket with quick mounting clamps. It has 3/8" ports, a 5 µm filter element and regulates 0.15 - 0.4 MPa (20 - 58 psi).
- TypeF.R.L. combination
- Port size3/8"
- Pressure range0.15 - 0.4 MPa (20 - 58 psi)
- Filtering grade5 µm
- Bowl materialPC
- Drainsemi-auto + manual
- Pressure gaugeCircular, MPa / psi
- Weight1300 g
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac GAC F.R.L. Unit GAC30010LW
Delivering cleaned, regulated and lubricated air for pneumatic systems, this AirTAC GAC30010LW combines a filter, regulator and lubricator on a single L-shape bracket. The 3/8in port pairs with a 5 um element to trap fine particles before they reach precision valves. Because the lubricator sits last in the sequence, oil mist is introduced downstream of the regulator seat, preventing fouling of the pressure-control mechanism.
This lower-pressure type regulates between 0.15-0.4 MPa (20-58 psi), making it suitable for sensitive actuators rather than high-force cylinders. A circular gauge is fitted, reading MPa/psi for the default PT thread, so operators can verify the setpoint at a glance. The unit carries a 1300 g mass and uses a 60 cc condensate bowl paired with a 98 cc oil reservoir to set the maintenance interval.
Airtac GAC F.R.L. Unit GAC30010LW Technical Specifications
| Model | Airtac GAC F.R.L. Unit GAC30010LW |
|---|---|
| Series | GAC300 F.R.L. combination |
| Port size | 3/8" (PT thread) |
| Filtering grade | 5 µm |
| Pressure range | 0.15 - 0.4 MPa (20 - 58 psi) |
| Type | Lower pressure |
| Bowl material | PC |
| Drain type | Semi-auto drain + manual drain |
| Fluid | Air |
|---|---|
| Max. pressure | 1.0 MPa (145 psi) |
| Proof pressure | 1.5 MPa (215 psi) |
| Temperature range | -5 to +70 °C (unfreeze) |
| Capacity of drain bowl | 60 cc |
| Capacity of oil bowl | 98 cc |
| Recommended lubricant | ISO VG 32 or equivalent |
| Weight | 1300 g |
Specifications follow the official AirTAC GAC catalogue (pages 216-217). Air must not freeze in the unit. The fitted circular gauge reads in MPa / psi, set by the PT thread code.
Model Code: Airtac GAC F.R.L. Unit GAC30010LW
| GAC300 | GA300 series F.R.L. unit — sets ports, bowl capacity and weight. |
|---|---|
| (blank) | Bowl material: PC. Available on this body: PC (blank), Metal (C), Nylon (N). |
| 10 | Port size 3/8". This body offers 08 = 1/4", 10 = 3/8", 15 = 1/2". |
| (blank) | Drain: Semi-auto drain + manual drain. |
| L | Lower pressure type — 0.15 - 0.4 MPa (20 - 58 psi). This body offers Standard (S) or Lower pressure (L). |
| (blank) | Circular pressure gauge fitted. |
| W | Filtering grade 5 µm. |
| (blank) | PT thread; gauge scale MPa / psi. |
| (blank) | No reverse-flow valve. |
Constituent units, orderable separately as spares: GAF300-10 filter, GAR300-10 regulator, GAL300-10 lubricator — all three share this body and port.
Size Class & Flow Envelope
- GAC2001/8"-1/4" · 1750 L/min
- GAC3001/4"-1/2" · 3000 L/min
- GAC4003/8"-1/2" · 6000 L/min
- GAC5003/4" · 7000 L/min
- GAC6003/4"-1" · 12000 L/min
Figures are the end of the flow curve plotted in the AirTAC catalogue at 0.7 MPa inlet pressure — a sizing envelope for comparing bodies, not a rated flow. Read the catalogue curve for a real duty point. Outlet pressure falls as flow rises, so size a body with headroom above your peak demand.
| This model | GAC300 · 3/8" · curve to 3000 L/min |
|---|---|
| One size down | GAC200 |
| One size up | GAC400 (curve to 6000 L/min) |
| Build order | Filter → bracket → regulator → lubricator |
Where the Airtac GAC F.R.L. Unit GAC30010LW Is Used
Laboratory Pneumatics
Feeds low-pressure air to sensitive analytical instruments and fluid dispensing heads that require a stable 0.4 MPa maximum supply.
Textile Spinning Frames
Conditions air for delicate tensioning cylinders and guide actuators, using the 5 um element to protect fine internal clearances from grit.
Small Assembly Jigs
Supplies metered oil mist and regulated pressure to lightweight pick-and-place grippers that cannot tolerate full 0.9 MPa shop line pressure.
Is the Airtac GAC F.R.L. Unit GAC30010LW the Right Air-Prep Unit?
Choose this 3/8in body when a machine requires very fine 5 um filtration and a low-pressure ceiling of 0.4 MPa, stepping up from the GAC200 which offers a 1750 L/min flow envelope plotted at 0.7 MPa inlet compared to this body's 3000 L/min curve. The PC bowl is standard, and the semi-auto plus manual drain pair requires an operator to cycle the valve or rely on the pressure-drop release. If the downstream line must remain oil-free, omit the lubricator and choose a filter-regulator instead. The constituent parts are separately orderable as GAF300-10, GAR300-10 and GAL300-10. Note that 0.4 MPa is 44% of the 0.9 MPa ceiling offered by the standard type, so select this L-type only if the application will never demand higher pressure.
Quick checklist
- ✓ Body size for your peak flow (3/8" here)
- ✓ Standard 0.9 MPa or lower-pressure 0.4 MPa
- ✓ Bowl material: PC (blank), Metal (C), Nylon (N)
- ✓ Drain: semi-auto + manual, or automatic
- ✓ Element 40 µm or 5 µm
- ✓ Thread & gauge scale (PT / G / NPT)
Installation & Maintenance Notes
- check Install with the airflow arrow: filter first, lubricator last.
- check Keep inlet pressure at or below 1.0 MPa (145 psi).
- check Fill the oil bowl with ISO VG 32 or equivalent only.
- check Drain condensate before the 60 cc bowl fills.
- check Keep the unit above freezing (-5 to +70 °C, unfreeze).
- check Support the 1300 g unit on its bracket, not on the tubing.
The lubricator adds an oil mist downstream of the regulator. If any part of the line must stay oil-free, use a filter-regulator instead of an F.R.L. combination on that branch.
Airtac GAC F.R.L. Unit GAC30010LW FAQ
This lower-pressure unit regulates from 0.15-0.4 MPa (20-58 psi) against a max pressure of 1.0 MPa (145 psi) and a proof pressure of 1.5 MPa (215 psi). It operates from -5 to 70 C, weighs 1300 g, and pairs a 60 cc drain bowl with a 98 cc oil bowl. The recommended lubricant is ISO VG 32.
The W code specifies a 5 um element, which traps far finer particles than the standard 40 um grade, making it ideal for precision valves. The L type code limits the regulation ceiling to 0.4 MPa, ensuring the unit cannot accidentally over-pressurize delicate downstream actuators.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC Air-Preparation Units
Request a Quote for Airtac GAC F.R.L. Unit GAC30010LW
Send us the quantity, thread type (PT / G / NPT) and destination. We confirm price, stock and lead time — usually within 7-8 hours.