
The AirTAC GC300-08 FRL Unit (GC30008ALF1T) is a genuine G-series three-unit F.R.L. combination: a separate filter, a separate regulator and a separate lubricator assembled as one air-preparation station. It has PT1/4" ports, a 40 µm element, a automatic drain and regulates 0.15 - 0.9 MPa (20 - 130 psi).
The GC series is AirTAC's three-unit F.R.L. combination: a separate air filter, pressure regulator and lubricator built as one set, so a single connection to the air line delivers filtered, regulated and oil-mist lubricated compressed air. This order code has NPT ports (the T in the code); the PT and G versions are separate order codes. Maximum inlet pressure is 1.0 MPa (145 psi); with the automatic drain, the regulator adjusts across 0.15-0.9 MPa (20-130 psi), and we can confirm the ceiling of the low-pressure type on request. Operating temperature is -5 to 70 C, non-freezing, and the 300 size uses polycarbonate bowls.
This is a genuine AirTAC part sold by an authorised distributor. Flow for the GC series is published as performance curves rather than a single rated figure, so ask us to confirm sizing and any datasheet value on request before ordering. Order code GC30008ALF1T has NPT ports (the T in the code) for North American pipe fittings.
| Model | AirTAC GC300-08 FRL Unit (GC30008ALF1T) |
|---|---|
| Series | GC300 F.R.L. combination |
| Composition | Filter + regulator + lubricator (3 units) |
| Port size | PT1/4" (NPT thread) |
| Filtering grade | 40 µm |
| Regulating range | 0.15 - 0.9 MPa (20 - 130 psi) |
| Pressure type | Low-pressure type |
| Fluid | Compressed air |
|---|---|
| Max. working pressure | 1.0 MPa (145 psi) |
| Temperature range | -5 to +70 °C (unfreeze) |
| Drain type | Automatic drain |
| Bowl material | PC |
| Pressure gauge | Fitted — square, MPa scale |
| Reflux valve | Not fitted |
Specifications follow the official AirTAC G-series air-preparation data. The regulating band is set by the drain type: automatic and differential-pressure drains regulate 0.15 - 0.9 MPa, a manual drain regulates 0.05 - 0.9 MPa. The low-pressure type adjusts over a lower band than standard; we confirm the exact figures from the factory datasheet. The combination has no separate bracket code — the three units couple together with their own mounting hardware. Flow curves, weight and outline dimensions are not published in our data set — ask us and we will confirm from the factory datasheet.
| GC300 | G-series F.R.L. combination, 300 body — sets the port range. |
|---|---|
| 08 | Port size PT1/4". This body offers 08 = PT1/4", 10 = PT3/8", 15 = PT1/2". |
| A | Drain: Automatic drain — this also sets the regulating band (0.15 - 0.9 MPa (20 - 130 psi)). |
| L | Low-pressure type. Blank is standard, L is the low-pressure type. |
| (blank) | Pressure gauge fitted (blank). |
| F | Gauge shape: Square. C is round, F is square. |
| 1 | Gauge scale: MPa. 1 is MPa, 2 is psi, 3 is bar. |
| (blank) | Filtering grade 40 µm. Only 40 µm (blank) and 5 µm (W) exist. |
| T | NPT thread. PT is the default; G is BSPP and T is NPT. |
| (blank) | No reverse-flow valve (the default). |
Field order is size, port, drain, type, gauge, shape, scale, grade, thread, reflux — there is no bracket position on a combination. Constituent units, orderable separately as spares: GF300-08 filter, GR300-08 regulator and GL300-08 lubricator.
A GC is three separate units, so the filter and the regulator can each be serviced or replaced on their own. A GFC is the two-unit set, where filtering and regulating share one body — shorter, but the two functions come as one part. Both filter, regulate and lubricate.
| This model | GC300 · PT1/4" · 40 µm |
|---|---|
| One size down | GC200 |
| One size up | GC400 |
| Two-unit equivalent | GFC300-08 |
| Build order | Filter → regulator → lubricator |
Feeds clean, regulated, lubricated air to the tool-clamp and pallet-clamp cylinders of a vertical machining centre, with the automatic drain keeping condensate out of the clamp circuit during unattended shifts.
Conditions the air feeding the cylinder-driven taping and folding heads on a carton sealing conveyor, so consistent regulated pressure and a light oil mist keep the sealing action repeatable across the shift.
Filters water and particulate from booth air, holds a steady regulated pressure at the gun and meters lubrication to the trigger valve, with the automatic drain coping with moisture-heavy compressor air.
Step up or down through sizes 200, 300, 400 and 600 to match port size and flow demand; the 300 size here carries 1/4 inch NPT ports. Choose the drain that fits your maintenance routine: automatic (this model) for hands-off condensate removal, manual for periodic draining, or the differential-pressure default. Keep the 40 um element for general plant air, or move to the W variant for 5 um filtration. The embedded square gauge reads in MPa (scale 1); This order code has NPT ports (the T in the code); the PT and G versions are separate order codes.
Flow is published as curves, not a single rating, so send us your line pressure and air demand and we will confirm the correct size against the datasheet before you order.
AirtacDistr lists every GC300-08 order code with its price on one page at https://airtacdistr.com/products/airtac-gc300-08-three-unit-frl
Quick checklist
The PC bowls must not be cleaned with solvents — wipe them with a dry cloth. The lubricator adds an oil mist downstream of the regulator. If any branch of the line must stay oil-free, take that branch off before the lubricator, or use a GR300-08 regulator with a GF300-08 filter on that branch.
AirTAC publishes GC-series flow as performance curves rather than a single rated figure, so we do not quote one number on this page. Tell us your line pressure and downstream demand and we will confirm the correct size against the datasheet on request.
The A in the code means the filter bowl drains condensate automatically as it collects, with no operator attention. Manual-drain (M) and differential-pressure (blank) versions of the same unit are catalogue options if you prefer a different routine.
T selects NPT port threads, the North American taper pipe standard. Without it the same order code has PT (Rc) ports, and with G it has G (BSPP) ports; body, function and dimensions do not change.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity, thread type (PT / G / NPT), gauge scale and destination. We confirm price, availability and lead time — usually within 7 hours.