
The AirTAC GC400-15 FRL Unit (GC40015ALNT) is a genuine G-series three-unit F.R.L. combination: a separate filter, a separate regulator and a separate lubricator assembled as one air-preparation station. It has PT1/2" ports, a 40 µm element, a automatic drain and regulates 0.15 - 0.9 MPa (20 - 130 psi).
GC40015ALNT is the 400-size, three-unit F.R.L. combination from AirTAC's G series: a separate air filter, pressure regulator and lubricator working together as one set to clean, regulate and oil-mist-lubricate compressed air. This configuration is built for 1/2 in. This order code has NPT ports (the T in the code); the PT and G versions are separate order codes. Maximum working pressure is 1.0 MPa (145 psi) and the operating temperature range is -5 to 70 C, non-freezing.
This is a genuine AirTAC part. The G series F.R.L. family spans sizes 200, 300, 400 and 600, with a choice of drain type, filtration grade, gauge and thread; Published flow data appears as curves rather than a single rating, so we confirm flow and datasheet figures for your application on request.
| Model | AirTAC GC400-15 FRL Unit (GC40015ALNT) |
|---|---|
| Series | GC400 F.R.L. combination |
| Composition | Filter + regulator + lubricator (3 units) |
| Port size | PT1/2" (NPT thread) |
| Filtering grade | 40 µm |
| Regulating range | 0.15 - 0.9 MPa (20 - 130 psi) |
| Pressure type | Low-pressure type |
| Fluid | Compressed air |
|---|---|
| Max. working pressure | 1.0 MPa (145 psi) |
| Temperature range | -5 to +70 °C (unfreeze) |
| Drain type | Automatic drain |
| Bowl material | PC |
| Pressure gauge | Not fitted |
| Reflux valve | Not fitted |
Specifications follow the official AirTAC G-series air-preparation data. The regulating band is set by the drain type: automatic and differential-pressure drains regulate 0.15 - 0.9 MPa, a manual drain regulates 0.05 - 0.9 MPa. The low-pressure type adjusts over a lower band than standard; we confirm the exact figures from the factory datasheet. The combination has no separate bracket code — the three units couple together with their own mounting hardware. Flow curves, weight and outline dimensions are not published in our data set — ask us and we will confirm from the factory datasheet.
| GC400 | G-series F.R.L. combination, 400 body — sets the port range. |
|---|---|
| 15 | Port size PT1/2". This body offers 10 = PT3/8", 15 = PT1/2". |
| A | Drain: Automatic drain — this also sets the regulating band (0.15 - 0.9 MPa (20 - 130 psi)). |
| L | Low-pressure type. Blank is standard, L is the low-pressure type. |
| N | No pressure gauge (N). |
| (blank) | Gauge shape: Factory standard. C is round, F is square. |
| (blank) | Gauge scale: Factory standard. 1 is MPa, 2 is psi, 3 is bar. |
| (blank) | Filtering grade 40 µm. Only 40 µm (blank) and 5 µm (W) exist. |
| T | NPT thread. PT is the default; G is BSPP and T is NPT. |
| (blank) | No reverse-flow valve (the default). |
Field order is size, port, drain, type, gauge, shape, scale, grade, thread, reflux — there is no bracket position on a combination. Constituent units, orderable separately as spares: GF400-15 filter, GR400-15 regulator and GL400-15 lubricator.
A GC is three separate units, so the filter and the regulator can each be serviced or replaced on their own. A GFC is the two-unit set, where filtering and regulating share one body — shorter, but the two functions come as one part. Both filter, regulate and lubricate.
| This model | GC400 · PT1/2" · 40 µm |
|---|---|
| One size down | GC300 |
| One size up | GC600 |
| Two-unit equivalent | GFC400-15 |
| Build order | Filter → regulator → lubricator |
Conditions air for tipper, tail-lift and door actuator circuits built on commercial vehicle bodies, where no local gauge is needed because pressure is read at the cab panel.
Installed on workshop ring-main drops to feed air tools and blow-off guns, with the automatic drain handling condensate on lines that see intermittent use.
Supplies cleaned, regulated and lubricated air to pneumatic actuated valves on a treatment plant skid, with pressure indication handled by the panel's own instrumentation.
Match the 400 size and 1/2 in. NPT ports to your pipe run, stepping to 200/300 or 600 as the circuit demands. The drain here is automatic; manual and differential-pressure are the other coded options on the filter bowl. Filtration is the 40 um standard element, with the 5 um W grade available for finer air. The N in the code means no gauge - choose a gauge version (square, in MPa, psi or bar scales) if the regulator setting needs local readout. This order code has NPT ports (the T in the code); the PT and G versions are separate order codes.
Flow for this family is published as curves, not as a single rated figure, so ask us to confirm sizing against your application before ordering.
AirtacDistr lists every GC400-15 order code with its price on one page at https://airtacdistr.com/products/airtac-gc400-15-three-unit-frl
Quick checklist
The PC bowls must not be cleaned with solvents — wipe them with a dry cloth. The lubricator adds an oil mist downstream of the regulator. If any branch of the line must stay oil-free, take that branch off before the lubricator, or use a GR400-15 regulator with a GF400-15 filter on that branch.
AirTAC publishes G series flow as curves rather than a single rated figure, so we do not state a number on the page. Give us your operating pressure and demand and we will confirm the flow from the datasheet on request before you order.
N means this unit is supplied without a gauge. If you want local pressure readout, the same set is available with the embedded square gauge in MPa (1), psi (2) or bar (3) scales - for example the GC40015ALF1. All other decoded features stay the same.
T selects NPT port threads, the North American taper pipe standard. Without it the same order code has PT (Rc) ports, and with G it has G (BSPP) ports; body, function and dimensions do not change.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity, thread type (PT / G / NPT), gauge scale and destination. We confirm price, availability and lead time — usually within 7 hours.