AirTAC 3V100M-14 3V-F Base (3V100M14F)
The AirTAC AirTAC 3V100M-14 3V-F Base (3V100M14F) is a genuine 3V-F manifold base manifold base for 14 stations on one shared air supply. A base is a machined block: it carries no coil and no solenoid, so the valves that sit on it are ordered separately.
- Valve type3/2-way (3-port, 2-position)
- Stations14
- Series3V-F manifold base
About the AirTAC 3V100M-14 3V-F Base (3V100M14F)
The 3V100M14F is a machined manifold base for AirTAC 3V-series 3/2 solenoid valves. Fourteen valve stations share one common air supply, so a single feed line replaces fourteen individual plumbing runs. The base itself carries no coil: it has no voltage, no electrical state and no power draw of its own.
This is a genuine AirTAC part, and the valves that sit on it are ordered separately. Across the 3V1/3V2/3V3 valve family you can specify normally closed or normally open, any of five coil voltages (AC220V, DC24V, AC110V, AC24V, DC12V), and DIN plug or flying-lead entry. Valve pressure, flow and coil-power figures are not published on this page - send us an RFQ and we will pull them from the datasheet for you.
AirTAC 3V100M-14 3V-F Base (3V100M14F) Technical Specifications
| Model | AirTAC 3V100M-14 3V-F Base (3V100M14F) |
|---|---|
| Series | 3V-F manifold base |
| Item form | Manifold base (no coil, no solenoid, no initial state) |
| Stations | 14 |
| Port size | Confirm from the datasheet — ask us |
| Thread | PT |
| Operating pressure | Confirm from the datasheet — ask us |
|---|---|
| Flow coefficient | Confirm from the datasheet — ask us |
| Temperature | Confirm from the datasheet — ask us |
| Protection | Confirm from the datasheet — ask us |
Model Code: AirTAC 3V100M-14 3V-F Base (3V100M14F)
| 3V-F manifold base | Body. |
|---|---|
| 14F | 14 stations in one assembly. |
| PT | Port thread. PT ships from stock; G and NPT are available to order. |
What a 3/2 Valve Does
A 3/2 valve has three ports — supply, outlet and exhaust — and two states. It either feeds the outlet or vents it to exhaust, and that is the whole job.
That makes it the right valve for a single-acting (spring-return) cylinder, on/off air blow, a clamp, switching a vacuum generator or suction cup, and piloting a larger valve.
It cannot run a double-acting cylinder. A double-acting cylinder needs air alternately on two sides, which takes a 5-port valve — the AirTAC 4V series.
Where the AirTAC 3V100M-14 3V-F Base (3V100M14F) Is Used
Parcel sorting gates
A sorting conveyor where each stopper gate or diverter runs on a single-acting cylinder, with one 3/2 valve per gate mounted on the same base.
Multi-clamp fixtures
A machining fixture plate with rows of spring-return clamps, each released or clamped by its own valve from one shared air feed.
Tidy control wiring
An automation panel where mounting all coils on one manifold lets a single wiring loom run the length of the base instead of fourteen separate drops.
Is the AirTAC 3V100M-14 3V-F Base (3V100M14F) the Right Part?
Plan each station before ordering: every valve position needs its own state (NC holds no air at the outlet until energised; NO does the opposite on power loss), its own port size (M5, 1/8in, 1/4in or 3/8in), its own coil voltage to match the panel, and its own entry type. Valves are ordered separately from the base.
We do not hold published flow figures for this family, so ask us to confirm sizing against each actuator before you commit. If you need a 3-port valve with published flow and coil-power figures today, look at the documented 3V2 and 3V3 bodies. For a double-acting cylinder, the AirTAC 4V series is the right choice.
Confirm before you order
- ✓ Port size and thread (PT from stock; G / NPT to order)
- ✓ Initial state — NC or NO, ordered up front
- ✓ Coil voltage matches your controller output
- ✓ Electrical entry — DIN plug or flying lead
- ✓ Single valve, bare base, or complete assembly
- ✓ Single-acting duty, not double-acting
Installation & Wiring Notes
- check Use clean air filtered to 40µm or finer.
- check Use the manual override to test before powering up.
- check Leave the exhaust port clear, or fit a silencer.
- check Blank any unused station on the base before pressurising.
- check Wiring by qualified personnel, per AirTAC documentation.
AirTAC 3V100M-14 3V-F Base (3V100M14F) FAQ
The base is a passive block - pressure, flow and coil-power figures belong to the valves you order separately. Send an RFQ and we will confirm those datasheet figures for your chosen valve codes. If you need published flow and coil power in hand right now, the documented 3V2 and 3V3 valve bodies carry them.
One machined block with 14 valve positions on a single shared air supply, which means one feed line, one mounting point and one wiring run. Valves are ordered separately, and each can be a different state, port size, voltage and entry. Note that 3/2 valves suit single-acting cylinders only - a double-acting cylinder needs a 5-port valve from the AirTAC 4V range.
Authorized Export Seller
Genuine AirTAC parts produced by the AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC 3V Valves
Request a Quote for AirTAC 3V100M-14 3V-F Base (3V100M14F)
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.