Airtac 3V-F Base 3V200M3F
The AirTAC Airtac 3V-F Base 3V200M3F is a genuine 3V-F manifold base manifold base for 3 stations on one shared air supply. A base is a machined block: it carries no coil and no solenoid, so the valves that sit on it are ordered separately.
- Valve type3/2-way (3-port, 2-position)
- Stations3
- Series3V-F manifold base
About the Airtac 3V-F Base 3V200M3F
The 3V200M3F is a machined manifold block for three 3/2 solenoid valves. Instead of plumbing and wiring three separate valves, you bolt them to one base, feed it with a single air line, and bring one wiring drop to the panel side. Every position still switches its own outlet under its own coil, so three independent functions - a clamp, a blow nozzle, a pilot signal - can share one tidy air supply.
This listing is the base only: the three valve bodies are ordered separately, so you pick the state (NC or NO), the coil voltage and the electrical entry for each position. It is a genuine AirTAC part. We do not publish pressure or flow figures for this family, but our engineers will confirm the datasheet values for the exact valves you choose on request.
Airtac 3V-F Base 3V200M3F Technical Specifications
| Model | Airtac 3V-F Base 3V200M3F |
|---|---|
| Series | 3V-F manifold base |
| Item form | Manifold base (no coil, no solenoid, no initial state) |
| Stations | 3 |
| Port size | Confirm from the datasheet — ask us |
| Thread | PT |
| Operating pressure | Confirm from the datasheet — ask us |
|---|---|
| Flow coefficient | Confirm from the datasheet — ask us |
| Temperature | Confirm from the datasheet — ask us |
| Protection | Confirm from the datasheet — ask us |
Model Code: Airtac 3V-F Base 3V200M3F
| 3V-F manifold base | Body. |
|---|---|
| 3F | 3 stations in one assembly. |
| PT | Port thread. PT ships from stock; G and NPT are available to order. |
What a 3/2 Valve Does
A 3/2 valve has three ports — supply, outlet and exhaust — and two states. It either feeds the outlet or vents it to exhaust, and that is the whole job.
That makes it the right valve for a single-acting (spring-return) cylinder, on/off air blow, a clamp, switching a vacuum generator or suction cup, and piloting a larger valve.
It cannot run a double-acting cylinder. A double-acting cylinder needs air alternately on two sides, which takes a 5-port valve — the AirTAC 4V series.
Where the Airtac 3V-F Base 3V200M3F Is Used
Rotary indexing table clamps
Spring-return clamp cylinders on a small indexing fixture can each be fed and vented by one valve position, with fail-safe release when power drops if NC valves are fitted.
Drilling jig hold-down
A single-acting hold-down on a drilling jig toggles from one station while a neighbouring station runs a part-blow nozzle to clear chips between cycles.
Chip blow-off at the machine
One station gives an intermittent air pulse to clear chips from a machined pocket, while the other two keep clamping duties fed from the same supply.
Is the Airtac 3V-F Base 3V200M3F the Right Part?
Three stations is the compact end of the range: enough for a small fixture or a test bench that needs two or three spring-return functions, without paying for unused positions. When you order the valves, match each coil voltage to the panel supply that will feed it - a coil cannot be rewired to another voltage - and choose DIN plug or flying-lead entry to suit the cabinet. Because we do not hold flow figures for the 3V2 valve family in-house, ask us to confirm the sizing of each valve against its actuator before you order. If you need published flow and coil power straight away, the documented 3V2 (1/8in and 1/4in) and 3V3 (1/4in) bodies carry them, and a double-acting cylinder calls for a 5-port valve from the AirTAC 4V series instead.
Confirm before you order
- ✓ Port size and thread (PT from stock; G / NPT to order)
- ✓ Initial state — NC or NO, ordered up front
- ✓ Coil voltage matches your controller output
- ✓ Electrical entry — DIN plug or flying lead
- ✓ Single valve, bare base, or complete assembly
- ✓ Single-acting duty, not double-acting
Installation & Wiring Notes
- check Use clean air filtered to 40µm or finer.
- check Use the manual override to test before powering up.
- check Leave the exhaust port clear, or fit a silencer.
- check Blank any unused station on the base before pressurising.
- check Wiring by qualified personnel, per AirTAC documentation.
Airtac 3V-F Base 3V200M3F FAQ
A base is unpowered pipework, so what matters is the valve you mount on it. Send us the 3V2 valve code you plan to fit and we will confirm its pressure range, flow and coil power from the datasheet. If you want those numbers published before you enquire, the 3V2 and 3V3 valve bodies are the documented ones in this family.
No. The base is sold on its own and the three valve bodies are ordered separately, which is deliberate: it lets you choose a different state, coil voltage and electrical entry for each position on the same manifold.
Authorized Export Seller
Genuine AirTAC parts produced by the AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC 3V Valves
Request a Quote for Airtac 3V-F Base 3V200M3F
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.